Results 1 to 7 of 7

Thread: XCR-M Operator's / Owner's Manual

  1. #1
    CGN Regular Xero's Avatar
    Join Date
    Apr 2007
    Location
    Calgary, AB
    Posts
    289

    XCR-M Operator's / Owner's Manual

    Hey everyone, I was able to get a direct PDF copy of the Owner's / Operator's Manual for the XCR-M directly from Robinson Armament. I wasn't able to find a public link to download this anywhere when looking for it, so I figured I'd throw it on Dropbox for everyone to benefit from.

    Before you read though, please be aware of the corrections posted by Grumpy Wolverine directly below this post (thanks Grumpy).
    XCR-M Manual 31Jan12.pdf

    Hope this helps some folks out. Enjoy!
    Last edited by Xero; 07-03-2014 at 02:46 PM.

  2. #2
    Business Member Grumpy Wolverine's Avatar
    Join Date
    Jul 2013
    Location
    Look over your shoulder
    Posts
    95
    That manual has some improper information in it. It says to break your rifle in on gas setting number 4. Please do not do this. Turn your gas setting down to the lowest setting it will function properly on and break it in there. Then after a few hundred rounds see if you can set it down even lower.
    Also the torque spec for the barrel bolt is 250 inch pounds, not 200.
    If you have any questions please call or e-mail:

    Phone: (204) 748-2454
    E-mail: sales@wolverinesupplies.com Retail Sales


  3. #3
    CGN Regular Xero's Avatar
    Join Date
    Apr 2007
    Location
    Calgary, AB
    Posts
    289
    Alright, I updated the first post a bit. If you find any other inconsistencies with the manual perhaps you can update you post listing them?

    Cheers,
    Xero

  4. #4
    Business Member Grumpy Wolverine's Avatar
    Join Date
    Jul 2013
    Location
    Look over your shoulder
    Posts
    95
    Sure will do, but I think those are the two biggest ones. The rest of it is to remember to run these guns very very very well lubricated.
    If you have any questions please call or e-mail:

    Phone: (204) 748-2454
    E-mail: sales@wolverinesupplies.com Retail Sales


  5. #5
    CGN Regular Xero's Avatar
    Join Date
    Apr 2007
    Location
    Calgary, AB
    Posts
    289
    This is, of course, a joke.

    How to lubricate an XCR-M:
    1. Lock bolt to the rear position.
    2. Expel entire bottle of frog lube into action.
    3. Cycle action until smooth.

    That about right?

  6. #6
    CGN Regular tavares86's Avatar
    Join Date
    Oct 2012
    Location
    GTA
    Posts
    393
    Quote Originally Posted by Xero View Post
    This is, of course, a joke.

    How to lubricate an XCR-M:
    1. Lock bolt to the rear position.
    2. Expel entire bottle of frog lube into action.
    3. Cycle action until smooth.

    That about right?
    Haha
    Member: CSSA

    ΜΟΛΩΝ ΛΑΒΕ

  7. #7
    Business Member Grumpy Wolverine's Avatar
    Join Date
    Jul 2013
    Location
    Look over your shoulder
    Posts
    95
    Quote Originally Posted by Xero View Post
    This is, of course, a joke.

    How to lubricate an XCR-M:
    1. Lock bolt to the rear position.
    2. Expel entire bottle of frog lube into action.
    3. Cycle action until smooth.

    That about right?
    Actually you couldn't go wrong with that method. More lube is better than less lube.
    If you have any questions please call or e-mail:

    Phone: (204) 748-2454
    E-mail: sales@wolverinesupplies.com Retail Sales


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •