Who's got KeyMod! Midwest, Noveske, BCM, Fortis, Seekins

[ctcs]

Midwest Industries SS Keymod Free Float Handguards back in stock

12" & 15" - in Black and Flat Dark Earth



12" - $229.99

15" - $249.99

MI Aluminum Key Mod Rail Sections



2.1" Section $24.99

3.75" Section $32.99

Noveske KeyMod QD Direct Attach Swivel



$24.99

Noveske KeyMod 1.035" Ring Flashlight Mount



$84.99

Noveske KeyMod Scout Light Mount



$76.99

BCM Gunfighter keymod Nylon Rail Section



3", 4" and 5.5" - From $15.99

Fortis REV KeyMod Handguard



9", 12", 14" - From $199.99

Seekins Precision MCSR V2 Handguard Rail



10" - $249.99

Midwest Industries Tavor KeyMod Handguard

• Easy Install, replaces factory plastic with no weapon alteration
• Made to accept Keymod rail sections and accessories
• One five slot Keymod rail included
• Lightweight, rugged construction of 6061 aluminum, hard coat anodized for a lifetime of service
• 5.4oz without rail, 6.3oz with 5 slot rail
• Black or Flat Dark Earth

$159.99

Also available

Midwest Industries Tavor Handguard Light Mount

• Easy install, replaces the standard MI handguard end cap with no weapon alteration
• Available for 1.0 inch diameter lights
• Mounting hardware included
• Constructed of 6061 aluminum, hard coat anodized for a lifetime of service
• Black or Flat Dark Earth

$54.99

[juancarlos]

Any MI Keymod panel covers or any keymod panel covers?

[ctcs]

Not yet - still unavailable to us

[shawn]

Are you going to bring in any of the BCM hand guards in 15"?

And what is the point of having a keymod rail which was designed to eliminate the need for rail covers and to make the hand guard slimmer, if you buy rails and rail covers to put on the keymod hand guard?

Shawn

[juancarlos]

Are you going to bring in any of the BCM hand guards in 15"?

And what is the point of having a keymod rail which was designed to eliminate the need for rail covers and to make the hand guard slimmer, if you buy rails and rail covers to put on the keymod hand guard?

Shawn

I don't see why you would care about my shooting prefereces but to answer your question, I am not planning on putting any rails or rail covers on. I am planning on putting hanguard panels on which mount directly to the handguard as I like having a defined grip point. I am guessing from the amount of post you have that you will probably tell me it is silly and you don't use them so neither should I because you are always right, etc, etc.

[ChrisAlston]

Nice looking stuff! Do you have plans to bring in the MI Extended KeyMod Handguards for the Tavor?

[ctcs]

Just the standard length one at the moment.

[rtracer13]

Any chance of getting the Fortis in with the FSB cut out (ie: fortismfg.com/ar15-fortis-REV-free-float-rail-system-CAR-cutout) ?

[ffgats]

I don't see why you would care about my shooting prefereces but to answer your question, I am not planning on putting any rails or rail covers on. I am planning on putting hanguard panels on which mount directly to the handguard as I like having a defined grip point. I am guessing from the amount of post you have that you will probably tell me it is silly and you don't use them so neither should I because you are always right, etc, etc.

In my case its for for the Heat especially the part close to the Gas Block, I dont wear gloves everytime,but after a long string of fire I dont want to melt my MANICURE.

[shawn]

I don't see why you would care about my shooting prefereces but to answer your question, I am not planning on putting any rails or rail covers on. I am planning on putting hanguard panels on which mount directly to the handguard as I like having a defined grip point. I am guessing from the amount of post you have that you will probably tell me it is silly and you don't use them so neither should I because you are always right, etc, etc.

Defensive much lol

Get over yourself it was a simple question, I was curious as to why you wanted too as maybe you had a good reason.

Shawn