I think there is promise for 165 and 168 still, but it will require some handload tuning. Hence why we are all anticipating Jerry's findings!
BCL102 Range Review, SECOND RANGE TRIP POST 123!!!
- Thread starter Jay
- Start date
I think there is promise for 165 and 168 still, but it will require some handload tuning. Hence why we are all anticipating Jerry's findings!
We have been told it is Armalite thread not DPMS. It is in the FAQ thread. No one has tested this yet. I have both to test I just don't have a good enough vise to do it with at the moment.
Ok ill order up the Armalite one 
This is gonna be an expensive Brownells order. lol...
MI Rail
BCM stock and Grip
.308 Vice block
AR10 nut wrench
JP .308 Buffer Spring
SSA-E Trigger
308 Raptor CH
Hopefully im not forgetting anything. lol...
This is gonna be an expensive Brownells order. lol... MI Rail
BCM stock and Grip
.308 Vice block
AR10 nut wrench
JP .308 Buffer Spring
SSA-E Trigger
308 Raptor CH
Hopefully im not forgetting anything. lol...
In fact, imma go get a new vise now so I can find out That is assuming my barrel nut wrench i have works...
Wow that will be a nice setup! You will love the rifle. I can't stop fondling mine. She hasn't let me down!
That is assuming my barrel nut wrench i have works...Ok ill order up the Armalite one
MI Rail
BCM stock and Grip
.308 Vice block
AR10 nut wrench
JP .308 Buffer Spring
SSA-E Trigger
308 Raptor CH
Hopefully im not forgetting anything. lol...
Wow that will be a nice setup! You will love the rifle. I can't stop fondling mine. She hasn't let me down!
I measured it out, and it should. I am moving to a 12" hand guard as well.
what in the heck is going on with this?
I cant seem to figure it out. The nut in front of the barrel nut is attached to the threading (receiver extension?) and the barrel nut itself doesnt look like it can slide over it.
I cant seem to figure it out. The nut in front of the barrel nut is attached to the threading (receiver extension?) and the barrel nut itself doesnt look like it can slide over it.
what in the heck is going on with this?
I cant seem to figure it out. The nut in front of the barrel nut is attached to the threading (receiver extension?) and the barrel nut itself doesnt look like it can slide over it.
Just a thought. Loosen the outer one that the handguard attaches to first. This should unlock it and then allow you to loosen the inner one that has the wrench flats on it. Things should then screw right off.
Here are 3/5/10 shot groups all the same load. Started in the center and went clockwise for one shot each until the targets got their designated number of shots. About 1-2 mins between shots.
At 215 rounds now with 10 malfunctions, all of which happened in the first 100 rounds.
At 215 rounds now with 10 malfunctions, all of which happened in the first 100 rounds.
Attachments
- Location
- Fort St John B.C.
Ok ill order up the Armalite one
MI Rail
BCM stock and Grip
.308 Vice block
AR10 nut wrench
JP .308 Buffer Spring
SSA-E Trigger
308 Raptor CH
Hopefully im not forgetting anything. lol...
i would suggest a reaction rod as well..... pretty sure brownells has a house brand one, geiselle is nice to.
Yup working on order #2 since I couldn't fit it all in the first one ....lol...
Im trying to figure out what Buffer and spring to grab as well if I should grab a spare bolt. Looks like the Brownells rod is only 46$
They are a few different buffers and spring combos, Does the 102 use a rifle or carbine buffer ? Love the JP springs, I used them all the time in my AR builds.
Nice. I am super stoked right now. Probably going to do a paint job on the Handuguard at some point, but otherwise loving it! Thanks to SSG9 again for the handguard! It is indeed armalite threaded.
Basically the first nut was to help index the barrel nut as some suggested.
Basically the first nut was to help index the barrel nut as some suggested.
