- Location
- Mission B.C.
Ok boys and girls has any one found a source for the CZ 452/455 single shot adaptor? I can not seem to find any in Canada.
CZ 452/455 single shot adaptor?
- Thread starter koikeeper67
- Start date
- Location
- Mission B.C.
KND: Do you have a good pattern for them? I found one on line and a friend of mine printed it for me but it is not very good as it will not lock into the mag well, and just when I think I have it locked it it pops out when I cycle the bolt.
Rrabill: This is what I have been doing but it is very finicky as you need to push the round half way into the chamber for it to work. Then some times the ejector dose not grab the round properly and I have to fish the spent case out.
Jabol: I was wondering about the Lowey one. Is it a proper molded part or dose it look to be 3D printed? I cant find any pictures of it so I have to ask is the top of the adapter ( where the round sits) flat or concave so the round will lay in properly?
Thanks for the help everyone.
Rrabill: This is what I have been doing but it is very finicky as you need to push the round half way into the chamber for it to work. Then some times the ejector dose not grab the round properly and I have to fish the spent case out.
Jabol: I was wondering about the Lowey one. Is it a proper molded part or dose it look to be 3D printed? I cant find any pictures of it so I have to ask is the top of the adapter ( where the round sits) flat or concave so the round will lay in properly?
Thanks for the help everyone.
Last edited:
Makes sense. That would be annoying to have to place it in the chamber each time rather than just dropping it in and go.
If you have some to spare I'd buy two for my 452.
- Location
- British Canuckistan
does the adapter enhance the accuracy at all or is it just to bring a rifle into rule compliance.
- Location
- Mission B.C.
loading single shot can improve accuracy as the bullet dose not get distorted or damaged by the magazine or when loading or cycling from the magazine.
I do seem to be getting better groups more consistently when loading single shot. It also slows down your rate of fire which can help keep you claim and
focused when behind the trigger.
I do seem to be getting better groups more consistently when loading single shot. It also slows down your rate of fire which can help keep you claim and
focused when behind the trigger.
- Location
- Mission B.C.
Jabol: that would be great if you could take some pics for me, no rush when ever you have free moment.
RabidM4U5 : I do have an email in to Wolverine as they seem to carry a lot of bits and pieces for CZ rifles.
RabidM4U5 : I do have an email in to Wolverine as they seem to carry a lot of bits and pieces for CZ rifles.
easyrider604
CGN Ultra frequent flyer
- Location
- Greater Vancouver, BC
Hello Jabol,
If it is ok with you, I would like to have three single-shot adapters, one each for my 3 x CZ452s, please. My postal code is V3H 4Z4 British Columbia (for shipping cost)
Please PM me the price of your 3D prints plus the cost of shipping. I can give you my Canada Post Venture Card number for the lowest shipping cost which also includes $100 insurance.
Thanks much
I have a single shot adaptor and two 455's.
Testing with the SSA against a five shot and ten shot magazine at 100 yards has some different components.
The ten round mag fully loaded did not fare as well and that may be due to the force required to get the tenth round in or shooting too fast.
Using the 10 round mag with only 5 rounds, the two are comparable.
Taking the extra time to single load is probably the best as there is no distortion to the round. With a five round magazine there is a shift towards speeding up.
While I only found small marks on lead bullets when they were carefully removed from the chamber the other possibility might be removing or shifting the lubricant.
A friend had some bullets that had been sitting in the sun and the lubricant had gravitated towards the point creating a blob that was flat where it contacted the container. Accuracy was horrible until he wiped the excess off. Shooting during hot weather softens the lubricant and the properties shift as does the accuracy.
CCI SV in paper boxes versus the plastic trays appear to use different lube but it may be volume used. The plastic tray variety has a barely noticeable trace of lube. The paper box ones have more and during colder weather some extra force is required to chamber. When single loading the club rifles and testing for best accuracy with the two CCI SV loadings all six rifles showed a preference.
Testing with the SSA against a five shot and ten shot magazine at 100 yards has some different components.
The ten round mag fully loaded did not fare as well and that may be due to the force required to get the tenth round in or shooting too fast.
Using the 10 round mag with only 5 rounds, the two are comparable.
Taking the extra time to single load is probably the best as there is no distortion to the round. With a five round magazine there is a shift towards speeding up.
While I only found small marks on lead bullets when they were carefully removed from the chamber the other possibility might be removing or shifting the lubricant.
A friend had some bullets that had been sitting in the sun and the lubricant had gravitated towards the point creating a blob that was flat where it contacted the container. Accuracy was horrible until he wiped the excess off. Shooting during hot weather softens the lubricant and the properties shift as does the accuracy.
CCI SV in paper boxes versus the plastic trays appear to use different lube but it may be volume used. The plastic tray variety has a barely noticeable trace of lube. The paper box ones have more and during colder weather some extra force is required to chamber. When single loading the club rifles and testing for best accuracy with the two CCI SV loadings all six rifles showed a preference.
Last edited:
It's KND who 3D prints the adaptors not Jabol.
easyrider604
CGN Ultra frequent flyer
- Location
- Greater Vancouver, BC
Oooops, my bad, sorry.
