Let's See Your WK!!!

[-raqh-]

Coming along! Just need the BCM Mod 3 foregrip, a better stock, maybe real magpul, and the ACT trigger... for now.

That is pretty nice. 15 inches handguard?

And people have been mentionning trouble with metal mags, how is yours ?

 

[stoop14]

Also interested in this hand guard, any modification needed for install?

Driller, I'm really liking the simplicity of your WK with nothing more than irons. I think I'll throw a set on my next WK and call it done.

That is pretty nice. 15 inches handguard?

And people have been mentionning trouble with metal mags, how is yours ?

 

[Jamjor]

TNA super mlok handguard, 15 inch. Took 5 minutes to install on the factory nut. When my WK was at Kodiak for the guide rod plate issue, Owen loosened the screws for me so that was nice.

Metal mags ran completely flawlessly. These and my LAR15 mags. In fact my WK was purchased from westrifle, and I never got the here mags. Just two steel stanag.

 

[iceangler650]

Pretty much done setting mine up maybe order rwa take down pivot pin and considering the fixed carbine stock and a foregrip for target shooting.

Which metal mags are most you guys finding work well in your WK?
And bulk ammo? I have A.E and Barnaul in 55grain some 62 grain fusions I bought for hunting but have not shot anything except A.E 55gr

 

[Anonymouse]

finally got my handguard on. just gotta cut off the beaver tail on my magpul k2 grip and bolt it on then i think i'm done messing with it.

 

[Ustauk]

Watch the port on the gas block when you shoot it with the 15. I'm assuming with the TNA 15"? My left hand got blasted by the gas coming out of the piston system since the TNA rail had more cut outs on it than the factory rail.

Ever thought about buying M-LOK rail covers? I have type 1 and 2 covers and type 1 are so soft and comfortable that’s why I like em!

Ive got the type 2s but my hands still get blasted because the covers don't actually cover the port.

Is there any solution to this? Is it only if you hold right at the gas block?

Found another potential solution on a video about the BRN-180, the handguard of which can apparently get burning hot from venting gas when you run Yankee-capacity magazines through it. They mentioned in the video that KE Arms makes an insulated handguard wrap, the SHTF+ wrap. Wolverine may be able to bring this in, or people up here may be able to home-make there own version. It might be useful in the winter, too; holding metal at -40, even with gloves, can get pretty cold

 

[Anonymouse]

This will have to do for now...

Found another potential solution on a video about the BRN-180, the handguard of which can apparently get burning hot from venting gas when you run Yankee-capacity magazines through it. They mentioned in the video that KE Arms makes an insulated handguard wrap, the SHTF+ wrap. Wolverine may be able to bring this in, or people up here may be able to home-make there own version. It might be useful in the winter, too; holding metal at -40, even with gloves, can get pretty cold

 

[RobbieLaidlaw]

My rifle is on order, am i going to have a hard time with my RMR red dot on here? Hows the height with the stock stock?

---

-Robbie L

 

[Anonymouse]

The RMR is made for pistols, the height over bore will probably be too low. If you really want to use the RMR on your WK you will need a scope riser.

My rifle is on order, am i going to have a hard time with my RMR red dot on here? Hows the height with the stock stock?

---

-Robbie L

 

[Vertebrae]

The RMR is made for pistols, the height over bore will probably be too low. If you really want to use the RMR on your WK you will need a scope riser.

Not trying to nitpick here, but the RMR was never intended for pistols. It was meant for carbines and PDW style guns, just as a small, light optic. It actually has a lot of issues when mounted on pistols, at least older gen units did, and the battery contact springs were weak enough where they would fail under slide reciprocation and the dot would flicker. Anyways... I have no WK, so carry on!

 

[swissey]

Modified mine a little. Getting the Muzzle break and handguard off was a bit of a hassle.

Should have probably cleaned the oil of the stock before taking the picture

https://adobe.ly/2KgeDhA

 

[uAJollyRogering]

Czechita Banana and Frankenczech's Monster.

 

[Chumlee Bumsnag]

Nothing special here. Just a set of Magpul Buis and a Vortex Strikefire Red dot. The red dot lines up perfectly on the top of the front sight blade.

 

[llotek]

Since I’m not a team member yet and can’t directly post photos,. Here’s a link to my wk180c

https://flickr.com/photos/148003506@N02/sets/72157706588956021

thats a beautiful rifle!...pretty much exactly what i imagined mine looking like, top to bottom..nice to see it in the flesh..

 

[rockport guy]

Where are people getting the Brass deflectors?

 

[Anonymouse]

Where are people getting the Brass deflectors?

 

[nelsonm64]

there are couple choices on ebay.

 

[CobraGT]

Czechita Banana and Frankenczech's Monster.

NICE stock mod!! That Vz stock is a great idea for the WK You just need some low-profile backup sights now.

 

[rockport guy]

there are couple choices on ebay.

Thanks, have one on the way!

 

[RobbieLaidlaw]