Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Dlask Arms XCR Stock Adapters **UPDATE**

  1. 12-12-2016, 01:35 PM #1
    Dlask Arms
    Dlask Arms is offline
    Business Member Dlask Arms's Avatar
    Join Date
    May 2007
    Location
    Delta, BC
    Posts
    3,009

    Dlask Arms XCR Stock Adapters **UPDATE**

    We have just finished a large run of our Robinson Armament XCR stock adapters. They are just out now for anodizing and should be back on the website by the end of this week. Sorry it took so long, we are just too busy to keep everything we make in stock all the time. The new adapters have a minor revision as well. A hole for a QD sling has been added, one on each side. (This was from requests we got to update the part.) Once they come back from coating they will be found here :

    http://dlaskarms.com/products/xcrtm-m4-stock-adapter

    *The picture will be updated once the parts are back in the shop.
    Cheers,
    Leigh
    Dlask Arms Corp.
    www.dlaskarms.com

    “Hard times create strong men. Strong men create good times. Good times create weak men. And, weak men create hard times.”
    Reply With Quote Reply With Quote
  2. 12-16-2016, 04:05 PM #2
    Dlask Arms
    Dlask Arms is offline
    Business Member Dlask Arms's Avatar
    Join Date
    May 2007
    Location
    Delta, BC
    Posts
    3,009
    These adapters have just come back from anodizing. Found here on the website :

    http://dlaskarms.com/products/xcrtm-m4-stock-adapter
    Cheers,
    Leigh
    Dlask Arms Corp.
    www.dlaskarms.com

    “Hard times create strong men. Strong men create good times. Good times create weak men. And, weak men create hard times.”
    Reply With Quote Reply With Quote
  3. 12-16-2016, 04:53 PM #3
    Patriot762x51
    Patriot762x51 is offline
    CGN Regular
    Join Date
    Mar 2016
    Posts
    270
    ??? Folding Charging handle ??? for XCR
    Reply With Quote Reply With Quote
  4. 12-16-2016, 07:09 PM #4
    Dlask Arms
    Dlask Arms is offline
    Business Member Dlask Arms's Avatar
    Join Date
    May 2007
    Location
    Delta, BC
    Posts
    3,009
    Quote Originally Posted by Patriot762x51 View Post
    ??? Folding Charging handle ??? for XCR
    No time for new projects. As it is these were out of stock for 6 months !
    Cheers,
    Leigh
    Dlask Arms Corp.
    www.dlaskarms.com

    “Hard times create strong men. Strong men create good times. Good times create weak men. And, weak men create hard times.”
    Reply With Quote Reply With Quote
  5. 02-19-2017, 10:48 AM #5
    NaviDave
    NaviDave is offline
    GunNutz
    Join Date
    Apr 2010
    Location
    Manitoba
    Posts
    1,168
    Is there an ETA for another run of these?
    Reply With Quote Reply With Quote
  6. 03-31-2017, 04:27 PM #6
    BadRonin
    BadRonin is offline
    CGN Regular BadRonin's Avatar
    Join Date
    Aug 2014
    Location
    The Great White North
    Posts
    432
    Any info on whether there will be another run?
    Or anyone selling these either new or used....?
    Post or PM please.
    Click, Bang.
    Reply With Quote Reply With Quote
  7. 03-31-2017, 04:36 PM #7
    Alphaskagg
    Alphaskagg is offline
    CGN Regular Alphaskagg's Avatar
    Join Date
    Oct 2015
    Location
    GTA
    Posts
    116
    same
    Reply With Quote Reply With Quote
  8. 04-13-2017, 05:32 PM #8
    Dlask Arms
    Dlask Arms is offline
    Business Member Dlask Arms's Avatar
    Join Date
    May 2007
    Location
    Delta, BC
    Posts
    3,009
    We have sorted out a small problem that for some reason has not shown up until now. The issue is that the XCR-M version *can* have the firing pin protrude to far out the rear and will need hit the stock adapters when the bolt cycles. We took half of our stock and bored a .560" diameter hole through them to rectify this and it was confirmed with a customer that brought it to our attention. (You were very patient and informative in helping us address this, thank you Sir.)

    So, bottom line, if you have the XCR-M with the rear protruding pin then you will need to wait a week until we can get the adapters re-anodized. If you have the XCR-L which does NOT have the rear protruding pin then you can once again find our stock adapters here :

    https://dlaskarms.com/products/xcrtm-m4-stock-adapter
    Cheers,
    Leigh
    Dlask Arms Corp.
    www.dlaskarms.com

    “Hard times create strong men. Strong men create good times. Good times create weak men. And, weak men create hard times.”
    Reply With Quote Reply With Quote
  9. 04-14-2017, 09:20 AM #9
    Longarm9
    Longarm9 is offline
    CGN Regular
    Join Date
    Jun 2015
    Location
    BC
    Posts
    148
    Quote Originally Posted by Dlask Arms View Post
    No time for new projects. As it is these were out of stock for 6 months !
    Too bad. A FAL style charging handle would be so damn sexy.
    Reply With Quote Reply With Quote
  10. 04-14-2017, 10:00 AM #10
    tk4959
    tk4959 is offline
    Newbie
    Join Date
    Oct 2016
    Location
    Burnaby,BC
    Posts
    6
    Awesome news. Just placed my order~~Thank you ,Leigh!
    Reply With Quote Reply With Quote
Page 1 of 2 12 LastLast
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules