Hey CGN, not a newbie necessarily, but new to this type of scenario. I have been shooting for 3 years now but only in the last year competitively. After trying out a G17 and MP9 for IDPA I actually came upon an SFP9 and have fallen in love with it. It's the only gun I shoot competitively. I also have a Steyr M40 as back up. My question is, I have fired about 2,000 rounds through (not a lot) but I have dry fired it about 12,000 times. I have of course done basic field stripping, cleaned and lubed, but should I be taking it to a Smith to give it a once over to see if anything needs replacing? I am not comfortable enough to start totally taking it apart to examine it. Plus not sure if I'd really know what to look for....I know there are YT videos if I wanted to go down that road. Thoughts if I even need to worry about anything yet?
Handgun maintenance
- Thread starter rayzorloo
- Start date
Still alive
CGN Ultra frequent flyer
- Location
- Rainy mosquito infested part of BC
Do you dry fire with snap caps?
Still alive
CGN Ultra frequent flyer
- Location
- Rainy mosquito infested part of BC
You are not wrong. However, I always err on the side of caution because I could be the exception that makes the case. Know what I mean?
With the 2000 round count, I'd say you're good for a few more thous. Esp. on a HK.
Look for cracks on the frame esp on the rails. Wear spots on the slide stop. And build up on the feed ramp. The rifling should be good for a lot more. Keep the gun clean and lubed and you should be fine.
If your groups start opening up or you get weird patterning, or weird ejection patterns or FTF, FTEs or issues igniting normal primers, then you should start looking at some deeper maintenance.
With the 2000 round count, I'd say you're good for a few more thous. Esp. on a HK.
Look for cracks on the frame esp on the rails. Wear spots on the slide stop. And build up on the feed ramp. The rifling should be good for a lot more. Keep the gun clean and lubed and you should be fine.
If your groups start opening up or you get weird patterning, or weird ejection patterns or FTF, FTEs or issues igniting normal primers, then you should start looking at some deeper maintenance.
meh, since you got a backup gun I'd run yours until something breaks 
HK's are fairly durable, VP9/SFP9 is the same as a glock, you can dry fire til the cows come home and not have any issues. No snapcaps required (they are nice to have, but NOT required).
HK's are fairly durable, VP9/SFP9 is the same as a glock, you can dry fire til the cows come home and not have any issues. No snapcaps required (they are nice to have, but NOT required).
Still alive
CGN Ultra frequent flyer
- Location
- Rainy mosquito infested part of BC
Did you ever get your 4.2" wheel gun?
Still alive
CGN Ultra frequent flyer
- Location
- Rainy mosquito infested part of BC
The make or break is always the reloads on a revolver. Are you loading with the support side or transferring the gun and loading strong side?
Why are you working on support hand shooting? For your own benefit? There's no requirement for support hand shooting in iDPA.
And, yes, pulling a DA trigger with your weaker side is difficult after a while. But pays off when you transfer the skill back to semi autos! Keep at it!
Why are you working on support hand shooting? For your own benefit? There's no requirement for support hand shooting in iDPA.
And, yes, pulling a DA trigger with your weaker side is difficult after a while. But pays off when you transfer the skill back to semi autos! Keep at it!
Still alive
CGN Ultra frequent flyer
- Location
- Rainy mosquito infested part of BC
Careful when you do the smack that you don't muzzle yourself. I only smack if the cases get really stuck. Most times, I just use my left hand thumb and push hard with gravity doing the job. I also find smacking and missing leads to great pain of the right palm!
