CanadianGunNutz.com logo, Firearms News and Classifieds in Canada

Page 2 of 23 FirstFirst 123456789101222 ... LastLast
Results 11 to 20 of 225

Thread: Modern Sporter photo thread

  1. #11
    Newbie
    Join Date
    Aug 2013
    Location
    Edmonton AB
    Posts
    19
    Here's mine, #17. Nothing special really, just stripped my Armalite M15 Target and loaded everything up in the MS with the exception of a new low profile gas block from TNA and 15" M-Lok handguard from Mag Dump. Currently at 10.2 Lbs.

    https://imgur.com/hwbHDs8
    Last edited by yowski; 02-08-2019 at 10:47 PM.

  2. #12
    Super GunNutz
    Join Date
    May 2015
    Location
    Onterrible
    Posts
    2,956
    Quote Originally Posted by yowski View Post
    Here's mine, #17. Nothing special really, just stripped my Armalite M15 Target and loaded everything up in the MS with the exception of a new low profile gas block from TNA and 15" M-Lok handguard from Mag Dump. Currently at 10.2 Lbs.

    ...
    "Arguing with idiots is like playing chess with a pigeon..... No matter how good you are, the bird is going to s#!t on the board and strut around like it won anyway."

  3. #13
    CGN Regular ThatM305Guy's Avatar
    Join Date
    Jun 2016
    Location
    North Texas
    Posts
    913
    *sits in the corner with an almost smug grin*
    I shall call it the bastard.
    Last edited by ThatM305Guy; 02-09-2019 at 12:42 AM.
    "Yeah, when we shot at the Americans it wasn't so bad because they would shoot back and roll on through.
    But when we shot at the Canadians they would get out and kill everyone." - Unknown

  4. #14
    Member
    Join Date
    Jul 2011
    Location
    Vancouver
    Posts
    55
    Quote Originally Posted by ThatM305Guy View Post
    *sits in the corner with an almost smug grin*
    I shall call it the bastard.
    Very nice. I'm deciding if I should go with Eotech halo + magnifier or a 1-8x scope. It's too hard to pick!

  5. #15
    CGN Regular
    Join Date
    Mar 2017
    Posts
    806
    Quote Originally Posted by Bomiheko View Post
    Very nice. I'm deciding if I should go with Eotech halo + magnifier or a 1-8x scope. It's too hard to pick!
    You are talking opposite ends of the spectrum. An eotech magnified is nothing even close to what a 1-8 would be. Not even the same dimension.
    "He who dares not offend, cannot be honest."
    - Thomas Paine

    "Oppression maketh a wise man mad"

  6. #16
    BANNED
    Join Date
    Nov 2011
    Location
    Republic of Alberta
    Posts
    3,771
    Quote Originally Posted by ThatM305Guy View Post
    *sits in the corner with an almost smug grin*
    I shall call it the bastard.
    Sick. Love the stock. What brake is that?

  7. #17
    CGN Regular ThatM305Guy's Avatar
    Join Date
    Jun 2016
    Location
    North Texas
    Posts
    913
    Quote Originally Posted by play.soccer View Post
    Sick. Love the stock. What brake is that?
    I made it out of one of the old chunky NEA ones. Was originally a two port. I threaded the OD and put straight knurl on the shoulder for the ratcheting barrel shroud/blast shield I have in the works. Have just been waiting to put it together so I can get a proper measurement from the brake to the end of the handguards internal relief.

    Also want to make annodized aluminum rods for the stock instead of steel, but one thing at a time.
    "Yeah, when we shot at the Americans it wasn't so bad because they would shoot back and roll on through.
    But when we shot at the Canadians they would get out and kill everyone." - Unknown

  8. #18
    GunNutz BCreserveMP's Avatar
    Join Date
    May 2013
    Location
    Victoria, BC
    Posts
    204
    Quote Originally Posted by ThatM305Guy View Post
    ...

    Also want to make annodized aluminum rods for the stock instead of steel, but one thing at a time.
    Any clearance issues with PDW rods along side the receiver? The MDI receiver is too wide for them.

    Any issues accessing the safety when the stock is full-forward?
    "Diplomacy is letting someone else have your way." - Lester Pearson
    "If I had to choose one ally in a fight it would be without a pause the Canadians. For decades they have learned to fight relentlessly with almost no resources. They fear nothing." - General Moshe Tamir, IDF

    CF, CCFR, CSSA

  9. #19
    CGN Regular ThatM305Guy's Avatar
    Join Date
    Jun 2016
    Location
    North Texas
    Posts
    913
    Quote Originally Posted by BCreserveMP View Post
    Any clearance issues with PDW rods along side the receiver? The MDI receiver is too wide for them.

    Any issues accessing the safety when the stock is full-forward?
    No clearance issues, they're literally a perfect fit.

    They are a little close to the safety when collapsed, but it's still serviceable. However you cant fully rack with the stock collapsed, as there isnt clearance for the charging handle.

    Also incase anyone was wondering, the anti rotation tab actually fits. A few swipes with a file on the tab and it lines up perfect.
    Last edited by ThatM305Guy; 02-09-2019 at 09:45 PM.
    "Yeah, when we shot at the Americans it wasn't so bad because they would shoot back and roll on through.
    But when we shot at the Canadians they would get out and kill everyone." - Unknown

  10. #20
    CGN Regular QuickDraw16's Avatar
    Join Date
    Sep 2009
    Location
    Burnaby
    Posts
    695


    More pics to follow

    It’s a simple low budget build.

    Parts list:
    CNA 20” 5.56 barrel 1:7
    OD green Magpul furniture (rifle length MOE handguard)
    Nickel Boron Brownells BCG
    Standard LPK (including trigger)
    A2 flash hider
    Aluminum gas block

    I made what tools I didn’t have already (castle nut wrench, flash hider wrench, and barrel nut wrench)


    All in, I’m very close to 2k after tax

    I have a Burris PEPR and a Leupold 2-7 scope for this rifle.
    Last edited by QuickDraw16; 02-18-2019 at 07:09 AM.
    They who give up essential liberty to obtain temporary safety, deserve neither liberty nor safety.
    -Ben Franklin
    One cannot successfully legislate an object to control an action. QuickDraw16

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •