Chargerguy
CGN frequent flyer
This thread is for the proud owners of Modern Sporter to post their builds.
Lol at the safe and fire symbols on the middle one
Modern Sporter photo thread
- Thread starter alberta tactical rifle
- Start date
Lol at the safe and fire symbols on the middle one
ATRS Modern Sporter Receiver Set
Maple Ridge Armoury V1 M-Lok 15" Handguard
Maple Ridge Armoury Match Nitride 5R 18.6" .223 Wylde Barrel (1/8" Twist, Rifle Length Gas System, Straight Fluting)
Superlative Arms Adjustable Gas Block Bleed Off (0.750")
Nightforce NX8
American Defense Manufacturing Recon 30mm QD Mount
Magpul MBUS Pro Offset Front and Rear
Daniel Defense M16 5.56 BCG
Radian Raptor Ambidextrous Charging Handle
BCM Gunfighter Grip Mod 2
Geissele Super Tricon Trigger
Phase 5 Extended Bolt Release V3
Magpul MOE SL Carbine Stock
Strike Industries, AR-15 Receiver Extension Kit, 7 Position Buffer Tube V2
Strike Industries AR-15 Aluminum Ultimate Dust Cover
JP SCS (when it comes in)
Radian Talon Ambi 45/90 Safety Selector
I have the same hand guard for my build. How does it line up with the upper?
Here's another one chambered in 5.56. It was built a little on the cheap but has room to grow. Weighs 6lbs 12oz bare.
-BCL (IBI) stainless 18.6" fluted mid-length gas 1:7" twist barrel
-Geisselle .750" stainless gas block
-MRA V1 M-LOK 13.5" handguard
-MRA stainless gas tube
-stainless bird cage flash suppressor
-BCL BCG
-BCM Gunfighter charging handle
-DPMS dust cover
-Anderson LPK
-BCL milspec buffer tube (a little loose in the CTR stock)
-ATRS's generic buffer and spring (unknown brand)
-Magpul CTR stock
-Burris PEPR 1" mount
-Leupold 3-9x40 American Marksman
2nd pic (with much nicer optic)
-Aero 30mm mount
-Premier 3-15x50 Gen II XR
I have around $2030 into it without scope or mount.
-BCL (IBI) stainless 18.6" fluted mid-length gas 1:7" twist barrel
-Geisselle .750" stainless gas block
-MRA V1 M-LOK 13.5" handguard
-MRA stainless gas tube
-stainless bird cage flash suppressor
-BCL BCG
-BCM Gunfighter charging handle
-DPMS dust cover
-Anderson LPK
-BCL milspec buffer tube (a little loose in the CTR stock)
-ATRS's generic buffer and spring (unknown brand)
-Magpul CTR stock
-Burris PEPR 1" mount
-Leupold 3-9x40 American Marksman
2nd pic (with much nicer optic)
-Aero 30mm mount
-Premier 3-15x50 Gen II XR
I have around $2030 into it without scope or mount.
Last edited:
- Location
- Swan River, MB
Got my uppers today! Was gonna post a pic of them stripped to "hold my spot here" but couldn't figure it out. Is it because my team membership expired?
Anyway, I am blown away by the machining and finish. They're absolutely beautiful. I'll put together my 6.5 grendel upper tonight and partial 5.56 as Im still waiting on parts for that one..
*UPDATE WITH PHOTOS* here's mine.. Waiting for my second lower (was an after thought originally getting 2 uppers with one lower, but why not have 2 complete rifles) 20" is in 6.5 grendel and 18.6" is obviously 5.56.
Anyway, I am blown away by the machining and finish. They're absolutely beautiful. I'll put together my 6.5 grendel upper tonight and partial 5.56 as Im still waiting on parts for that one..
*UPDATE WITH PHOTOS* here's mine.. Waiting for my second lower (was an after thought originally getting 2 uppers with one lower, but why not have 2 complete rifles) 20" is in 6.5 grendel and 18.6" is obviously 5.56.
Attachments
Last edited:
I ran into an issue with my trigger, so won’t be able to post up some groups , just yet.
What you see is,
Christensen Arms 20 inch ,1-8 twist Carbon fiber wrapped barrel.
TNA knights of the round table brake( it works
Battle Arms Development ridgeline 15 inch hand guard.
Raptor ambi CH
CTR stock
Brownells BCG
Leupold VX3i 4.5-14 LRP optic.
Just a touch over 6 lbs without optic
Just a touch over 8 lbs with optic
Last edited:
Here is my MS. Still waiting for JP SCS at this moment... I ordered rifle length gas system barrel and MRA send me one with midlength gas... Didn't notice until it is assembled by ATRS. I can not reach the adjustable gas block with the 17 inch handguard....
Definitely gonna switch to a low power variable scope, who have recommendation?
Mine have a little bit play between lower and upper, I placed some tape between these two parts and the play gone.
Last edited:
Fixed it for you
Thanks! I just cant seem to get pics to work right through my phone.
Build list:
Faxon 20" gunner barrel
Precision armament m4 72 brake
Odinworks 15.5" lightweight handguard
Brownells lightweight nitride bcg
Pws buffer tube
Geissele ssa-e trigger
Geissele maritime bolt catch
Ergo parts kit
Magpul grip and stock
Last edited:
Here is my MS. Still waiting for JP SCS at this moment... I ordered rifle length gas system barrel and MRA send me one with midlength gas... Didn't notice until it is assembled by ATRS. I can not reach the adjustable gas block with the 17 inch handguard....
Definitely gonna switch to a low power variable scope, who have recommendation?
Mine have a little bit play between lower and upper, I placed some tape between these two parts and the play gone.
Dude. That looks just about perfect.
Details?
- Location
- Red Deer, Alberta
Here is my MS. Still waiting for JP SCS at this moment... I ordered rifle length gas system barrel and MRA send me one with midlength gas... Didn't notice until it is assembled by ATRS. I can not reach the adjustable gas block with the 17 inch handguard....
Definitely gonna switch to a low power variable scope, who have recommendation?
Mine have a little bit play between lower and upper, I placed some tape between these two parts and the play gone.
Looking good!!
I have both Vortex strike eagle 1-6 & a older Primary Arms SFP 1-6 with 7.62x39 ACSS reticle for a 7.62x39 bolt gun. They are about the same quality optically, I bet they are made in the same factory. I'd go with the Primary Arms because of the reticle. I'd like to try the newer Primary Arms 1-6 with the FFP. I've looked through the Eotech Vudu 1-6 FFP and they are very nice. I also have a Kahles 1-6 and it is simply amazing, but honestly if I was buying today I'd save money and just buy the Eotech, I don't think the Kahles is $1200 better.
ATRS MS receiver
MRA 18.6 barrel 223 Wylde
17 battle arms development handguard
Superlative adjusting gas block
Lantac dragon brake
Ergo LPK
Triggertrch non adjustable ar trigger
Brownells lightweight BCG
Odin charging handle
Magpul UBR stock
JP SCS
Elcan 1/4 556 with chevron reticle lol
I don't see the point of a low mass BCG if you're going to add mass back with a heavier buffer.
Stupid photobucket....I couldn't attach pics for whatever reason....
This is Mike's 223 plinker upper for 3 gun/practical shooting/ coyote gun.
ATRS MS reciever set (just beautiful by the way)
UTG Minimalist Stock
Taccom lightweight buffer and spring
Brownells lightweight NiB BCG
Radian Raptor charging handle
Ergo grip
Stag standard safety
Velocity 3 lb flat trigger
Phase 5 bolt catch
Magpul extended magazine release
Chinese "M-lok" 15" handguard (sorry ATRS, Odin goes on the Valkyrie)
TNA custom order 223 Wylde barrel, 1 in 7, rifle length, medium profile, 2 lbs 9 oz (forget who made it)
Odin Adjustable gas block
Brownells stainless gas tube
Precision Armament M-11 brake
Vortex crossfire for now, waiting on Primary Arms ACSS to show up.
Comes up at 6 lb 14 oz unloaded with no optic.
7 lb 3 oz with crossfire.
Would be a full pound lighter with a pencil barrel but I've never been able to hold on to any accuracy with them.
Stupid photobucket....I couldn't attach pics for whatever reason....
This is Mike's 223 plinker upper for 3 gun/practical shooting/ coyote gun.
ATRS MS reciever set (just beautiful by the way)
UTG Minimalist Stock
Taccom lightweight buffer and spring
Brownells lightweight NiB BCG
Radian Raptor charging handle
Ergo grip
Stag standard safety
Velocity 3 lb flat trigger
Phase 5 bolt catch
Magpul extended magazine release
Chinese "M-lok" 15" handguard (sorry ATRS, Odin goes on the Valkyrie)
TNA custom order 223 Wylde barrel, 1 in 7, rifle length, medium profile, 2 lbs 9 oz (forget who made it)
Odin Adjustable gas block
Brownells stainless gas tube
Precision Armament M-11 brake
Vortex crossfire for now, waiting on Primary Arms ACSS to show up.
Comes up at 6 lb 14 oz unloaded with no optic.
7 lb 3 oz with crossfire.
Would be a full pound lighter with a pencil barrel but I've never been able to hold on to any accuracy with them.
Last edited:
- Location
- calgary alberta
It is supposed to be so I deleted a bunch of banter that should have been posted in the other threads.
Guys photos and a description of components, cool. Posting random comments just means folks wanting to see photos have to wade through a ton of junk to see what they want. Not so cool.
Think of it as having to deal with having to see a ton of commercials while wanting just to see the movie.
