Deleted
Last edited by Beeron; 03-09-2023 at 04:46 PM.
*FAIR WARNING* I LEAVE FEEDBACK FOR ALL TRANSACTIONS AND I EXPECT THE SAME.
Did you clean and lubed the pistol? Though I do not have this Olympia, my experience with 22 pistol/revolver with misfires is I would say good enough. Manufacturers has tolerances that varies. Even the powder they use might cause varying velocities as stated. Casing hardness also plays factor. Some brands has harder casing causing misfires and sometimes no fire at all. Extraction is also a factor in unusually harder casing. Bulk Ammo is hit and miss. I had good results with Blazer, Mini Mag, Federal 525, Fed Match, CCI SV, Win M22. Remy Golden Bullet is also good, but damn dirty. Going back to misfires, if you can fully strip the pistol down to the last screw (don't do this if you are not comfortable that you can reassemble it back). Pay attention to the extractor and firing pin. Make sure the extractor moves freely to catch the fired casing. The firing pin, make sure it slides inside out of the firing pin channel. Clean it with a fine grit abrasive paper if you can feel rough edges as I am not sure if the firing pin is machined or stamped. Clean the whole pistol of the factory lube as this lube is generally thick to protect the pistol from corrosion after production before it gets t the customer. Good luck.... Safe Shooting!
I was shooting my Olympia a week ago. Before, I cleaned thoroughly all “cosmoline” with Ballistol. The ammo I used was the CCI Standard Velocity (lead bullet), Aguila HV, AR Tactical and CCI Mini Mag. I had only two misfires with the CCI Mini Mag. But that was it. No misfires at all with other brands.
In one of two mags which came with the pistol, the CCI Stand. Velocity lead bullet was catching the magazine cutout and couldn’t move up. A bit of inside filing smoothed the edge of the cutout and everything is fine now. My Olympia very much likes the AR Tactical cartridges. Although, the accuracy with the other brands was also pretty good. The trigger pull weight is close to 4lbs.
I have large hands and the grip fits me like a glove. The two-hand hold gripping is also very comfortable.
I agree that the lack of the lack of slide stop lever is weird and the mag release button is completely un-ergonomic. But these are minor problems. After a while, one can used to it. I don’t quite understand why you are saying that you need to depress the release to feed a mag. I just give it a light smack with the open palm of my left hand and that’s it.
NFA CCFR CSSA
CPC PC Ontario
My magazine catch and mags behaved the same when I got them and I just kept forcing it in and now my the mag slides in great with a nice click. In my experience with all norinco firearns is that they need a break in period, especially the cheaper ones.
As for the misfires I'm not sure, havent got my paperwork yet to go to the range so I havent fired mine
I was shooting my Olympia a week ago. Before, I cleaned thoroughly all “cosmoline” with Ballistol. The ammo I used was the CCI Standard Velocity (lead bullet), Aguila HV, AR Tactical and CCI Mini Mag. I had only two misfires with the CCI Mini Mag. But that was it. No misfires at all with other brands.
In one of two mags which came with the pistol, the CCI Stand. Velocity lead bullet was catching the magazine cutout and couldn’t move up. A bit of inside filing smoothed the edge of the cutout and everything is fine now. My Olympia very much likes the AR Tactical cartridges. Although, the accuracy with the other brands was also pretty good. The trigger pull weight is close to 4lbs.
I have large hands and the grip fits me like a glove. The two-hand hold gripping is also very comfortable.
I agree that the lack of the slide stop lever is weird and the mag release button is completely un-ergonomic. But these are minor problems. After a while, one can used to it. I don’t quite understand why you are saying that you need to depress the release to feed a mag. I just give it a light smack with the open palm of my left hand and that’s it.
NFA CCFR CSSA
CPC PC Ontario
I recieved mine and it's great for the price, mine has a little spot that looks like the bluing wasnt done well or was warn off. Other than that I'm very happy with it, pistol has some weight in the hand and doesnt feel cheap. Machining is good, small seam on the barrel but great everywhere else. Recieved awesome customer service from marstar as well so shout out to them for that. The pistol fits the hand well and is super simple to disassemble. Really looking forward to trying it out.
One thing as well that I noticed is the spare aftermarket mags do not have plastic baseplate that is part of the grip while the magazine is in the pistol. Not a big deal by any stretch, just something I noticed. Also the mags didn't want to push into the pistol at first but once I forced it a few times it worked great.
Overall very pleased that I picked one of these up. Thanks marstar for the awesome price!
I concur with most of the above comments. However, I found the bluing to actually be pretty good and the gun had no real sharp edges to deal with. Giving the mags a good whack 8-10 times to smooth out the mag catch seemed to solve the problem of difficult insertion/removal. Yes, the mag release is a bit awkward to reach but not awful. My only real gripe (and not a big one at that) is that the safety was brutally hard to engage & disengage to the point where I had to hit it up and down about 15 times with a nylon punch to get it movable with my finger. Again, however, that seemed to smooth it out so i don't foresee a problem with this going forward.
Only one misfire out of 50 rounds of Federal bulk pack and that was a faulty round which I re-hit a couple of times with no detonation (good firing pin indents).
My only other issue is with adjusting the rear sight for windage. The screws are TINY, even making Ruger sight screws seem big by comparision. My gun was shooting to the left so I wanted to move the rear sight but all I had were jewellers screwdrivers with me which were not big enough to put sufficient leverage on the screw to move it. I'm still working up the nerve to use a more substantial screwdriver as the slot is so small i don't want to mess it up.
Overall still a great purchase for $200 and as with most Norinco guns I expect everything to have smoothed out considerably by the time I get a couple hundred rounds through it.
No misfire with CCI mini Mag, and I don't have to press the mag release to feed a mag.
Interestingly enough, the windage on the rear sight of my Olympia was set up absolutely perfect in the center. Some reviews on the TT-Olympia reported that after shooting the tiny rear sight screws could unscrew themselves and got lost. I unscrewed the left screw that is a bit larger than the right one, to expose the thread and squeezed a drop of blue Loctite (#242) on it. Just to be on the safe side.
Obviously, I share the opinion of others that for $199 (+tax&shipping) the Olympia is a great deal.
NFA CCFR CSSA
CPC PC Ontario