Page 21 of 27 FirstFirst ... 11131415161718192021222324252627 LastLast
Results 201 to 210 of 265

Thread: Poly 80 shipment update, November 30 2022

  1. #201
    CGN Regular sogone2day's Avatar
    Join Date
    Sep 2011
    Location
    Edmonton
    Posts
    554
    Quote Originally Posted by KaneZoR View Post
    Great job bringing in the P80 guns and frames and parts, you’ve made a lot of folks happy.

    On any future shipments might I suggest bringing in some g19 and g17 threaded barrels, lots of folks have picked up glocks in the past few weeks and many will be wanting to add comps as part of what they’re building, myself included.

    Thanks again!
    I got around this issue and bought a extra complete slide just incase. After i looked at aftermarket prices from other places they seem reasonably priced.

  2. #202
    CGN Ultra frequent flyer Johnyy's Avatar
    Join Date
    Jan 2013
    Location
    ON
    Posts
    3,027
    Quote Originally Posted by sogone2day View Post
    G19s use a different locking block barrel setup than a 17 as i understand for this. Dont quote me not sure why some work on gen5s and such.
    Ahh, Ya, it may just be bcuz this kit includes the 'locking block, is why it's listed only for 19, but other than that one piece, everything else should be cross compatible for the Gen 3 17/19's lower parts...I believe ? Anyone know if that is correct?

  3. #203
    Super GunNutz madcow's Avatar
    Join Date
    Sep 2005
    Location
    Edmonton
    Posts
    3,237
    Quote Originally Posted by Saskatoon Gunworks View Post
    I was absolutely convinced this wouldn't happen but...Very happy to report, after a lot of uncertainty, and being convinced we would not get our shipment across the border, we have just been informed that it has been cleared, we will have more Polymer80 parts!!!

    Good to hear that all the information I searched out was legit

  4. #204
    Business Member Saskatoon Gunworks's Avatar
    Join Date
    Jan 2010
    Location
    Saskatoon, SK
    Posts
    144
    Quote Originally Posted by madcow View Post
    Good to hear that all the information I searched out was legit

    Thank-you!

    Have had further conversations with local CBSA and was told they really don't know what is going on, as there has been no direct guidance from government, however, they did say don't attempt any more imports of handguns.

  5. #205
    CGN frequent flyer firebat's Avatar
    Join Date
    Jul 2016
    Location
    Edmonton
    Posts
    1,028
    Finally got my frame today, so the build is complete. I really like the grip angle and the trigger that has a very short reset. It looks very sexy with a match grade agency arms stainless steel barrel.

  6. #206
    CGN Regular sogone2day's Avatar
    Join Date
    Sep 2011
    Location
    Edmonton
    Posts
    554
    Quote Originally Posted by firebat View Post
    Finally got my frame today, so the build is complete. I really like the grip angle and the trigger that has a very short reset. It looks very sexy with a match grade agency arms stainless steel barrel.

    Pics?
    I just got my transfer completed. I got one to check the grip as well in fullsize against a glock 17s

  7. #207
    CGN Regular aka_ryan's Avatar
    Join Date
    Sep 2016
    Location
    Ontario
    Posts
    230
    This is to answer the other guy's question about g19/g17 locking block.

    Pre Gen5 Glock 19 and 17 use different locking blocks. Gen5 Glock changed to the same locking block for 19.5 and 17.5.

    Therefore, the Nomad lpk you see on Saskatoon's website works for 19.3 19.4 19.5 and 17.5, that's what they meant by 19/17.

    The same kit for Gen3 differs only in the magazine catch/release, which is for Gen3 only.

    I personally have not used these kits before, if anyone who bought them could chime in here on their fit and reliability that would be great. They seem to be very reasonably priced.

    Also for those who haven't noticed, Saskatoon also carries blank 19.4 and 17.5 slides for a very fair price for those whose planning on doing customized cut and cerakote. I wish they also offers 19.3 though.

    Cheers
    "Once they are gone, they are gone." -- Anonymous Sales Rep

  8. #208
    CGN frequent flyer firebat's Avatar
    Join Date
    Jul 2016
    Location
    Edmonton
    Posts
    1,028
    Quote Originally Posted by sogone2day View Post
    Pics?
    I just got my transfer completed. I got one to check the grip as well in fullsize against a glock 17s
    That's with the P80 slide, I'm waiting for a fancy custom one too.




  9. #209
    CGN Regular sogone2day's Avatar
    Join Date
    Sep 2011
    Location
    Edmonton
    Posts
    554
    Quote Originally Posted by firebat View Post
    That's with the P80 slide, I'm waiting for a fancy custom one too.



    Nice. I'm looking forward tongeeling the grip angle

  10. #210
    Member MrSkrewuvsky's Avatar
    Join Date
    Mar 2019
    Posts
    76
    Does anyone know if the optical cut only for RMR or Holosun can be installed as well?
    The fully assembled 19 slide did not come with any document for the specs.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •