^What ammo and gun oil?
My first sks 20 years ago grew the rust hairs that cleaned off. lesson learned, I clean it every time now out of good habit. Takes 2 mins once you've done it a couple times
^What ammo and gun oil?
My first sks 20 years ago grew the rust hairs that cleaned off. lesson learned, I clean it every time now out of good habit. Takes 2 mins once you've done it a couple times
It's true. I bought an SKS once where the seller, an elderly gentleman, indicated he never ran corrosive ammo through the gun. Well, when I got it home, I took it apart and sure enough the gas tube piston rod was seized in the gas tube. Orange corrosive bits all over the place. It was easy enough to clean it out and lube it, but unless he was the original owner of the 1950s SKS, doubtful he would have the whole history of whether any corrosive ammo was used it in before. I'd say the chances are 100% that at some point in its history, SOMEONE ran corrosive ammo through it (whether they knew it or not) and didn't bother to clean it properly. Some people check the bolt face and breech, don't see any corrosion and assume ammo was all good. It is really that gas tube and piston rod that will give you a decent indication. But as others mentioned, it's not an inordinate amount of effort to clean with hot water and such...it does require some effort but how much each owner decides to expend doing this will vary.
CCFR, CSSA, NRA (Life), CPC, CHP
I run 1970s east block ammo (East German, Czech, Romanian) through all of my x39 guns, including my CZ Bren and WS-MCR. I just hose down the bore with G96 bore solvent before I leave the range (upside down so that it runs into the gas system) and then pull it through and wipe down the gas system parts when I get home. Zero issues with corrosion.
As an aside, I got some red box Norinco non-corrosive ammo in a trade deal recently. That is the only time I’ve ever had issues with with cases getting stuck in the chamber, and in one case, the extractor breaking off part of the case rim. I’m sure it’s just a bad lot of ammo, but suffice it to say, I’d never pay the prices retailers are asking for that crap because it’s non-corrosive.
Easy come, easy go...
I'm in your boat. Getting an SKS as my first gun as well and corrosive ammo seems to be a good deal if it's safe.
It's no big deal.
Clean thoroughly after shooting corrosive ammo. Within a day or so. Dont leave it to sit for days.
Pour hot water down the bore to wash out the corrosive salts, then clean as normal. Or use windex, with ammonia, to neutralize the salts.
A little orange build up in a chrome lined barrel wont hurt it. But you can soon get pitting on the bolt face, the gas piston and in the gas tube.
OFGPA, OFAH, CCFR
In a gun that's easy to disassemble like an SKS, corrosive is fine to use.
Unlike some of the advice given here, I'll say use water to clean, plenty of it. Tepid water is perfectly fine to dissolve the salt. Hot water doesn't hurt, but it doesn't need to be. Then dry thoroughly, a hair dryer is helpful.
NB: Salt is not soluble in most modern bore cleaners. That is why you use water, plus its plentiful and cheap.
Use of the average bore cleaner alone will not remove the salt! I witnessed a beautiful handgun get ruined that way, the owner used bore cleaner, then oil. A week later the bore had lots of oily rust in it.
We are annoyed by the assumption on the part of certain public figures that the citizen should be able to prove the need for the citizen to acquire a means of protecting himself. The citizens personal needs are certainly no business of the state. Liberty, when it's in place, grants the right of the citizen to do what he chooses, as long as he does not stamp on the rights of others.
JEFF COOPER
[SIGPIC][/SIGPIC]
I'll add my voice to the chorus that corrosive is fine, just clean your rifle afterwards.
Cleaning corrosive salts doesn't have to involve water, which generally doesn't go well with steel and wood. I've yet to see anyone, upon spilling salt on a table or kitchen counter, grab a kettle of hot water to sluice down the area. Brushing salt off the table works fine; it doesn't need to be dissolved to remove it. Same with a rifle bore/action/gas system--a proper cleaning with oil will remove corrosive salts just fine without risking the unwelcome potential effects of water.
Remember High River! Who's protecting YOUR civil rights?
Bernier...who?
We are annoyed by the assumption on the part of certain public figures that the citizen should be able to prove the need for the citizen to acquire a means of protecting himself. The citizens personal needs are certainly no business of the state. Liberty, when it's in place, grants the right of the citizen to do what he chooses, as long as he does not stamp on the rights of others.
JEFF COOPER
[SIGPIC][/SIGPIC]
Neither does a whole bunch of other types of corruption found in a bore after shooting, yet magically solvent and oil combined with brushing and swabs seems to remove them. I can't explain what happened to your buddies handgun... but at the end of the day, you do you and those of us that don't find a need to dumping water down our barrels will do us. The issue are the chaps that do absolutely nothing in the way PMCS.
Last edited by armybuck041; 08-04-2023 at 08:52 PM.
Easy come, easy go...
Corrosive is fine, clean your gun after shooting it. Read the sks sticky, half way down the first page is the cleaning rundown. Pictures don’t seem to work anymore but it’s pretty self explanatory.
https://www.canadiangunnutz.com/foru...tion-*updated*