12.5" 870 Barrels Available?

[mmattockx]

Dlask no longer lists any 12ga barrels on their site (that I can find, anyway) and I see the NEA 14" barrels don't like to work with standard Wingmaster receivers. Where can I find a 12.5" barrel for my old 2.75" Wingmaster receiver?

Second question, what did the Dlask barrels cost when they were selling them?


Mark

 

[Outcast]

Canada ammo 12.5 grizzly barrel... Sponsor at top of page

 

[luke s]

grizz is the only option these days, fits just fine in my old wingmaster

 

[MrTwitch]

Dominion Arms Grizzly. Cheap, effective and looks just right on an actual Remington.

 

[mmattockx]

Canada ammo 12.5 grizzly barrel... Sponsor at top of page

grizz is the only option these days, fits just fine in my old wingmaster

Damn, I never even thought of Canada Ammo. Reasonable and in stock, hard to beat that.

Thanks,
Mark

 

[cosmicheretic]

Would the following fit on my Remington 870 Super Magnum?:


Spare 12.5" Barrel for Dominion Arms Grizzly/Remington 870 Shotguns - 12ga x 3" Chamber - Fixed cylinder bore - Brass bead sight - Matte blue finish

SKU: 87X125BARREL

 

[luke s]

Would the following fit on my Remington 870 Super Magnum?:


Spare 12.5" Barrel for Dominion Arms Grizzly/Remington 870 Shotguns - 12ga x 3" Chamber - Fixed cylinder bore - Brass bead sight - Matte blue finish

SKU: 87X125BARREL

I forget if its the super magnum or special purpose (likely the ladder) that doesnt accept standard barrels.

That being said I have mounted a 3.5" chamber barrel from a super magnum on that old wingmaster as well as 2 grizzlies, should be good to go

 

[highspeedlowdrag]

Slightly off topic, but do the Dominion Arms barrels come with a ball detent installed on the barrel ring? Thanks.

hsld.

 

[luke s]

They do not as grizzly shotguns have a tube based on an express model

 

[cosmicheretic]

I forget if its the super magnum or special purpose (likely the ladder) that doesnt accept standard barrels.

That being said I have mounted a 3.5" chamber barrel from a super magnum on that old wingmaster as well as 2 grizzlies, should be good to go

The 870 SuperMag does accept standard barrels as mentioned in some threads. Think I will just go ahead and order a couple barrels.

 

[MrTwitch]

Northeastern Arms has just posted that barrels are coming onto the market again. http://www.canadiangunnutz.com/forum/showthread.php?t=764131

 

[CZ_Brno]

grizz is the only option these days, fits just fine in my old wingmaster

Works on mine. Old Wingmaster for $200, 12.5 inch barrel for $150

 

[mmattockx]

Works on mine. Old Wingmaster for $200, 12.5 inch barrel for $150

That is exactly the combination I am looking for, awesome.


Mark

 

[GIGGIDY]

I also have a 12.5 Griz barrel from CanAm on my older 870 Wingmaster. I haven't use it a ton but initial tests found it to work flawlessly. I have to hold low to make hits but whatever. I was worried about the barrel nut backing off as there is no detent in the barrel ring as stated luke s by but so far it has stayed tight and not caused issue.

 

[CZ_Brno]

Some additional info. On my older 870 Wingmaster with the 12.5 Grizzly barrel from CanAm the gun is 32.75 inches overall length approximately. If I were to put on a pistol grip it would be shorter then the 660 millimeters (25.984252 inches) allowed. With a pistol grip on the Wingmaster I would probably need about a 14" barrel.

 

[freezer filler]

With a pistol grip on the Wingmaster I would probably need about a 14" barrel.[/QUOTE]


16"

 

[luke s]

16"

yep, and since they dont exist (or unobtanium)......... 18"

 

[DocBurN]

removed.. already answered in this thread