B.C. folding stock for 10/22 cause firing prob

[mooseman1]

i recently set up 2 10/22's with B.C. folder's, and both have issue's with the trigger group pin creeping too one side so that the trigger bind's and you have a single shot with 12lbs trigger, not alot of fun in the bush if it happen's every 25-50 round's,so to fix this i can use J.B. weld , nail polish or lock tight right?anyone else have this prob?

 

[22forever]

Here's what I used, works great. http://coolguyguns.com/webstore/index.php?main_page=product_info&cPath=11&products_id=3

 

[lone-wolf]

Fabsports has em
http://www.fabsports.ca/receiver-ruger-p-750.html?language=URL_LANGUAGE

Cheap solution: duct tape? I'd try nail polish(easily removed) before your other two ideas.

 

[Wham-O]

I have the same B.C. folding stock.
How do your pins slide? They should be snug to the inside of the stock?

 

[mooseman1]

I have the same B.C. folding stock.
How do your pins slide? They should be snug to the inside of the stock?

yea whamo it's the same stock,for some reason the pin holding the trigger&sear has enough room to creep to one side till the other side fall's out of the housing ,thus the trigger can pull sideways and bind.it's annoying when you have to field strip every 50 round's.

 

[Wham-O]

yea whamo it's the same stock,for some reason the pin holding the trigger&sear has enough room to creep to one side till the other side fall's out of the housing ,thus the trigger can pull sideways and bind.it's annoying when you have to field strip every 50 round's.

Are you sure you have the correct pin in that position??
Very strange....
If they are the correct pin(s), Lone-Wolf if right...a piece of duct tape should do the trick.
Are these old or fairly new trigger housings/pins?
Aluminum or polymer?

 

[mooseman1]

i have one new plastic one and one older aluminum one , yea the plastic one is worse,i'll try the duck tape on them ,seem's the stock has to much room right there.

 

[Hoboman]

Just a quick question? What is a B.C. folder? & where can I get one. Tried Cabela's & they won't ship. So how do I get a folding stock for ruger 10/22??

 

[Wham-O]

B.C. = Butler Creek (the manufacture)
Rimfire Sports sells them and ships to Canada.
Good Luck!

ht tp://www.rimfiresports.com/merchant.mv?Screen=PROD&Store_Code=RSC&Product_Code=FS10-B%2FS

 

[lone-wolf]

Mine was bought used, off the EE.
More BC folder pr0n:

 

[P of PDent]

B.C. = Butler Creek (the manufacture)
Rimfire Sports sells them and ships to Canada.
Good Luck!

ht tp://www.rimfiresports.com/merchant.mv?Screen=PROD&Store_Code=RSC&Product_Code=FS10-B%2FS

The Butler Creek folding stock for the 10/22 has been a good seller in the past however...the US govt. banned the export of these stocks a few years ago and are not available through legal sources. If anyone is exporting these to Canada they are certainly doing this without permits as these would not be approved and they are exposing themselves to a world of hurt if this is found out by the powers that be. Phil.

 

[Wham-O]

The Butler Creek folding stock for the 10/22 has been a good seller in the past however...the US govt. banned the export of these stocks a few years ago and are not available through legal sources. If anyone is exporting these to Canada they are certainly doing this without permits as these would not be approved and they are exposing themselves to a world of hurt if this is found out by the powers that be. Phil.

Hmmmmmmm?

Interesting Phil???

I wonder what Jerry Teo of Mysticprecision has to say about that??

ht tp://www.mysticprecision.com/wp/?p=578

 

[P of PDent]

If these stocks are being exported from the USA then they will not issue an export lic. except for military or LE. Shotgun stocks are not controled as they come under a different classification. Bushnell (who owns Uncle Mike's/Butler Creek) is now having most products produced in the Orient so they could in fact be imported directly from there and bypass the USA. Obviously exports regs change from time to time but I am not aware of anything recently. Phil.

 

[Juster]

Surely a blob of epoxy on the stock would fix this?

 

[lookout]

I have the same stock and had the same problem. A piece of tape as a guide, and JB weld to fill the gap on the stock where the pin protrudes is good medicine.
I'm around 10 000 rounds and counting after this fix...

 

[mooseman1]

Just a quick question? What is a B.C. folder? & where can I get one. Tried Cabela's & they won't ship. So how do I get a folding stock for ruger 10/22??

A BC folder is a Butler Creek folding stock and i might have a blued one spare for the right money,as i changed mine out for a ss one.they are hard to find.

 

[P of PDent]

We just took in a new (not in box) Butler Creek stainless steel folding stock for 10-22. It is priced at $150 (won't last long). Phil.

 

[mooseman1]

wow ok i was going to let mine go for $120