Barrel Tenon Size/Thread list
- Thread starter 22to45
- Start date
burnt_servo
CGN Ultra frequent flyer
- Location
- right in the middle of b.c.
i would be interested in that too
This was a "start" on a master list...goldie oldie now.
http://www.canadiangunnutz.com/forum/showthread.php?t=532496
If you have more, add to it and, maybe get yourself a "sticky"
http://www.canadiangunnutz.com/forum/showthread.php?t=532496
If you have more, add to it and, maybe get yourself a "sticky"
Some barrel shank drawings available here ----> http://ifile.it/259b1ot/Barrel_Shank_Dimensions_12_25_08.pdf
------------------------------------------------------
Edit: Use carefully, there are some errors I've found. (document not of my making )
------------------------------------------------------
Edit: Use carefully, there are some errors I've found. (document not of my making )
Last edited:
Hope this helps,
Barrel threads per inch
Browning 0.937 20 The A-bolt uses a threaded barrel (15/16" x 20 tpi).
Small ring mauser 0.98 12
Large ring mauser 1.10 12
FN-FAL 1.00 16
Remington 1.062 16
Ruger #1 1.0 16
Sako 1.030 16
Savage 1.055 20
1.120 20 (new) WSM, RUM, and SAUM calibers
The larger barrel shank will have a step down approximately 1/8" ahead of the barrel nut. If your rifle has a serial number with a "G" prefix, it is most probable it will have the larger shank.
Winchester 1.0 16
The following are the Shank Diameters and Receivers Diameters, and some t.p.i,, of some common firearms, Always ask and I will give this information on any BBL Shank and or receiver I have at that time.
Mauser standard Shank O mean Diameter same as before 1.100" receiver O 1.42",Mauser Small ring Shank o .980" receiver o 1.35",1917 or 1914 Enfields, Shank o 1.125" receiver 1.1375",1903 Springfield Shank 1.040" receiver 1.35",Win models 54 and 70 shank o 1.00",receiver 1.35",Remington 721 and 722 shank 1.05" and receiver 1.35".
Marlin 95 bbl wideth .955,shank .986 12 sg. cut tpi.
Mossberg 04M bbl width .750 with a shank of .637 extending 1.60 long.
Page-lewis bbl width .690 shank .505 wide 1.00 long.
Peabody single shot shank .965 and 10 sg. cut, t.p.i.
Premier slide action bbl width .750 wide shank .597 with 24 tpi v cut.
Remington model 31 bbl width 12 ga 1.204,16 ga 1.167,20 ga 1.180,shank width 12 ga 1.10,16 ga 1.028 20 ga 1.025 length of shank 12 ga .7018 16 ga .704 20ga .707the 12 and 16 ga have 14tpi sg treads and the 20 ga has 14 tpi v cut threads.
Remington 514 bbl width .755,shank wideth .590 shank lenth .755.
Remington rolling block cadet ,shank width .836 shank lenght 1.250 with 12 sq threads per inch.
Remington 11-48 12 ga bbl width 1.160,shank width 1.055,shank lenght .890 includes section with out threads.
Remington 33 bbl width .766,26 tpi v cut, shank length 1.00 overall with .300 treaded and .700 bare which measurers .606,thraded section od is .675 and bare sections od is .606.
Barrel thread sizes of some common Rifle actions, the first # is the Barrel Extension Diameter, The second # is the Threads per inch and the third is the type of thread. see more Barrel treads and shank sizes on about page 22.
Win, #1 and #2 single shot actions .821" ,16 tpi,Vee type.
Win, #3 Heavy single shot action .930"16 tpi,Vee type.
Win, Models 54 and 70, 1.00",16 tpi,Vee type.
Win, 07 model .746" ,20 tpi,vee type threads.
Win, 86 and 71 models .875" ,20 tpi ,vee type.
Win, models 92 and 53 models .805 20 tpi ,vee type.
Win, 94, 55, and 64 ,.805", 20 tpi and vee type threads.
Win, 95, .930" and 16 tpi,vee type threads.
Savage, 99...900" 12 tpi and square type threads.
Marlin, 93 and 36 models .778", 12 tpi and square type threads.
Standard Automatic,.996" and 10 tpi,square type threads.
Ballard, Single Shot,.950" ,18 tpi and vee type threads.
Sharps, Borchardt,.945" 16 tpi and vee type threads.
Stevens, ideal #44 single shot,.8125" , 20 tpi and vee type threads.
Stevens ,44 1/2 sible shot .875" and 16 tpi, vee type threads.
Springfield ,1.040" and 10 tpi and squared type threads.
Enfield,1.118", 10 tpi and squared type threads.
Rem,models, 30 and 720 1.118" and 10 tpi squared type threads.
Norwegian, krag 1.056", 12 tpi L.H,sqaured type threads.
Danish, Krag ,1.060", 12 tpi and vee type threads.
Mauser, model, 98 1.100", 12 tpi vee type threads.
Small ring sporting, Mausers, cz 33/40 .981", 12 tpi and vee type threads.
Mauser, 88 and 93 models .985" and 12 tpi and vee type threads.
Belgian, Mauser .995" and 12 tpi,vee type threads.
Austrian Steyr, 95, 1.060", 12 tpi and vee type threads.
Jap Ariskaka, 6.5 mm 1.026", 14 tpi and vee type threads.
Jap Ariskaka, 7.7mm,1.025", 17 tpi vee type threads.
Colt Woodman pistol Shank 1.525 with .800 non treaded,32 t.p.i on .555 and untreaded section is .455.
Colt police Positive, threaded section o.d is .455 and a lenght of .725 with a section 7/64 not threaded with a o.d of .338.32 tp.
Barrel threads per inch
Browning 0.937 20 The A-bolt uses a threaded barrel (15/16" x 20 tpi).
Small ring mauser 0.98 12
Large ring mauser 1.10 12
FN-FAL 1.00 16
Remington 1.062 16
Ruger #1 1.0 16
Sako 1.030 16
Savage 1.055 20
1.120 20 (new) WSM, RUM, and SAUM calibers
The larger barrel shank will have a step down approximately 1/8" ahead of the barrel nut. If your rifle has a serial number with a "G" prefix, it is most probable it will have the larger shank.
Winchester 1.0 16
The following are the Shank Diameters and Receivers Diameters, and some t.p.i,, of some common firearms, Always ask and I will give this information on any BBL Shank and or receiver I have at that time.
Mauser standard Shank O mean Diameter same as before 1.100" receiver O 1.42",Mauser Small ring Shank o .980" receiver o 1.35",1917 or 1914 Enfields, Shank o 1.125" receiver 1.1375",1903 Springfield Shank 1.040" receiver 1.35",Win models 54 and 70 shank o 1.00",receiver 1.35",Remington 721 and 722 shank 1.05" and receiver 1.35".
Marlin 95 bbl wideth .955,shank .986 12 sg. cut tpi.
Mossberg 04M bbl width .750 with a shank of .637 extending 1.60 long.
Page-lewis bbl width .690 shank .505 wide 1.00 long.
Peabody single shot shank .965 and 10 sg. cut, t.p.i.
Premier slide action bbl width .750 wide shank .597 with 24 tpi v cut.
Remington model 31 bbl width 12 ga 1.204,16 ga 1.167,20 ga 1.180,shank width 12 ga 1.10,16 ga 1.028 20 ga 1.025 length of shank 12 ga .7018 16 ga .704 20ga .707the 12 and 16 ga have 14tpi sg treads and the 20 ga has 14 tpi v cut threads.
Remington 514 bbl width .755,shank wideth .590 shank lenth .755.
Remington rolling block cadet ,shank width .836 shank lenght 1.250 with 12 sq threads per inch.
Remington 11-48 12 ga bbl width 1.160,shank width 1.055,shank lenght .890 includes section with out threads.
Remington 33 bbl width .766,26 tpi v cut, shank length 1.00 overall with .300 treaded and .700 bare which measurers .606,thraded section od is .675 and bare sections od is .606.
Barrel thread sizes of some common Rifle actions, the first # is the Barrel Extension Diameter, The second # is the Threads per inch and the third is the type of thread. see more Barrel treads and shank sizes on about page 22.
Win, #1 and #2 single shot actions .821" ,16 tpi,Vee type.
Win, #3 Heavy single shot action .930"16 tpi,Vee type.
Win, Models 54 and 70, 1.00",16 tpi,Vee type.
Win, 07 model .746" ,20 tpi,vee type threads.
Win, 86 and 71 models .875" ,20 tpi ,vee type.
Win, models 92 and 53 models .805 20 tpi ,vee type.
Win, 94, 55, and 64 ,.805", 20 tpi and vee type threads.
Win, 95, .930" and 16 tpi,vee type threads.
Savage, 99...900" 12 tpi and square type threads.
Marlin, 93 and 36 models .778", 12 tpi and square type threads.
Standard Automatic,.996" and 10 tpi,square type threads.
Ballard, Single Shot,.950" ,18 tpi and vee type threads.
Sharps, Borchardt,.945" 16 tpi and vee type threads.
Stevens, ideal #44 single shot,.8125" , 20 tpi and vee type threads.
Stevens ,44 1/2 sible shot .875" and 16 tpi, vee type threads.
Springfield ,1.040" and 10 tpi and squared type threads.
Enfield,1.118", 10 tpi and squared type threads.
Rem,models, 30 and 720 1.118" and 10 tpi squared type threads.
Norwegian, krag 1.056", 12 tpi L.H,sqaured type threads.
Danish, Krag ,1.060", 12 tpi and vee type threads.
Mauser, model, 98 1.100", 12 tpi vee type threads.
Small ring sporting, Mausers, cz 33/40 .981", 12 tpi and vee type threads.
Mauser, 88 and 93 models .985" and 12 tpi and vee type threads.
Belgian, Mauser .995" and 12 tpi,vee type threads.
Austrian Steyr, 95, 1.060", 12 tpi and vee type threads.
Jap Ariskaka, 6.5 mm 1.026", 14 tpi and vee type threads.
Jap Ariskaka, 7.7mm,1.025", 17 tpi vee type threads.
Colt Woodman pistol Shank 1.525 with .800 non treaded,32 t.p.i on .555 and untreaded section is .455.
Colt police Positive, threaded section o.d is .455 and a lenght of .725 with a section 7/64 not threaded with a o.d of .338.32 tp.
Here is a bit of info I cut and pasted in other places..
thanks for the info, I am contemplating putting a small ring mauser barrel in a M17 Enfield action, I was checking to see if I would have to rethread the barrel to make room for a bushing.
Enfield SMLE -
.687" Dia +.100 lip x .900" Root Dia x .997" Dia x 14 V-TPI.
Enfield P-14 -
.720"L +.045"Lip x 1.085" Root Dia X 1.125" Dia X 10 SQ-TPI.
Enfield 1917 -
.800" Dia x 1.085" Root Dia x 1.125" Dia x 1o SQ-TPI w/45-degree chamber cone.
Sako -
L46 = .845"L x .855"Dia x 16 V-TPI,
L57 = .984" Dia x 17 V-TPI,
L579 & early L61 = .870" L x 1.0" Dia x 16 V-TPI,
Late L61 = Same as L579, but 1.046" Dia.
Enfield Eddystone Model of 1917 barrel threads are 1.125 with 10 SQ T.R.I., length of barrel threads is .800 inch also stated as 1.125"x10, square threads.
The Browning BPCR and maybe all the Browning 1885's, as quoted to me on the BPCR Board, are .935" outside diameter, shank length is .920" and the threads are 20 per inch with a standard 60 degree form. Very similar to the Winchester 1885 but for the 20 threads per inch instead of 16 per inch in the Winchester.
Action threads length Reciver OD? other
Mauser lrg. Ring 1.1x12 1.41”
Mauser sm. Ring .98x12
CZ 550 1.1x12.7
BBK-02 1.1x12
Rem 700 1 1/16”x16 .885
1.0625x16
Win 70 1x16
Ruger 77 1x16 1.41”
Sako
Weatherby mk V 1.06x16 .7
1 1/16x16
Browning A-bolt
Ruger no. 1 1x16”
Rem Rolling block
No. 1 smokeless 1.055x12 square 1.43”
Win 1885 High wall
Sharps 1874
Savage 110 < 2001 1.05x20
Short magnum>2001 1.125x20 G series, noticeable step after threads
CRF 1 1/16x20
1.0625x20
Bolt Shotgun 1.1x20?
MRC 1999 1x16 UNF 2B .75
Enfield M-17 x10 square
Enfield SMLE
Mosin Nagant .97”x16 or 1x16”
Steyr M-95 1.020x14 tpi V .693” shank
Win 94 .809x20
Win 94 BB .875x28?
Rossi 92
Marlin 336 .775x12 square .85”
Marlin 1895 45-70 same as 336, 450 may have been changed to a v thread.
Savage 99
Norinco Win 1887 lever shotgun 12 ga. 1.1x26 proofed to 43ksi!
Norinco Win 1897 pump shotgun 12 ga. Proofed to 43ksi
__________________
thanks for the info, I am contemplating putting a small ring mauser barrel in a M17 Enfield action, I was checking to see if I would have to rethread the barrel to make room for a bushing.
Enfield SMLE -
.687" Dia +.100 lip x .900" Root Dia x .997" Dia x 14 V-TPI.
Enfield P-14 -
.720"L +.045"Lip x 1.085" Root Dia X 1.125" Dia X 10 SQ-TPI.
Enfield 1917 -
.800" Dia x 1.085" Root Dia x 1.125" Dia x 1o SQ-TPI w/45-degree chamber cone.
Sako -
L46 = .845"L x .855"Dia x 16 V-TPI,
L57 = .984" Dia x 17 V-TPI,
L579 & early L61 = .870" L x 1.0" Dia x 16 V-TPI,
Late L61 = Same as L579, but 1.046" Dia.
Enfield Eddystone Model of 1917 barrel threads are 1.125 with 10 SQ T.R.I., length of barrel threads is .800 inch also stated as 1.125"x10, square threads.
The Browning BPCR and maybe all the Browning 1885's, as quoted to me on the BPCR Board, are .935" outside diameter, shank length is .920" and the threads are 20 per inch with a standard 60 degree form. Very similar to the Winchester 1885 but for the 20 threads per inch instead of 16 per inch in the Winchester.
Action threads length Reciver OD? other
Mauser lrg. Ring 1.1x12 1.41”
Mauser sm. Ring .98x12
CZ 550 1.1x12.7
BBK-02 1.1x12
Rem 700 1 1/16”x16 .885
1.0625x16
Win 70 1x16
Ruger 77 1x16 1.41”
Sako
Weatherby mk V 1.06x16 .7
1 1/16x16
Browning A-bolt
Ruger no. 1 1x16”
Rem Rolling block
No. 1 smokeless 1.055x12 square 1.43”
Win 1885 High wall
Sharps 1874
Savage 110 < 2001 1.05x20
Short magnum>2001 1.125x20 G series, noticeable step after threads
CRF 1 1/16x20
1.0625x20
Bolt Shotgun 1.1x20?
MRC 1999 1x16 UNF 2B .75
Enfield M-17 x10 square
Enfield SMLE
Mosin Nagant .97”x16 or 1x16”
Steyr M-95 1.020x14 tpi V .693” shank
Win 94 .809x20
Win 94 BB .875x28?
Rossi 92
Marlin 336 .775x12 square .85”
Marlin 1895 45-70 same as 336, 450 may have been changed to a v thread.
Savage 99
Norinco Win 1887 lever shotgun 12 ga. 1.1x26 proofed to 43ksi!
Norinco Win 1897 pump shotgun 12 ga. Proofed to 43ksi
__________________
Some barrel thread sizes
If you can find a copy of the NRA "Gunsmithing Guide," you will find several pages of barrel thread diagrams. This is an excellent book for anyone who would like to do some home gunsmithing.
They still show up at gun shows, used book dealers, and on E-bay. It might still be in print or available from the NRA in the states.
.
If you can find a copy of the NRA "Gunsmithing Guide," you will find several pages of barrel thread diagrams. This is an excellent book for anyone who would like to do some home gunsmithing.
They still show up at gun shows, used book dealers, and on E-bay. It might still be in print or available from the NRA in the states.
.
