I sold a semi-auto Bren about 2 years ago. The transfer was held up until it was sent in for inspection.
Today I got this email:
Daniel Guay <Daniel.Guay@rcmp-grc.gc.ca>
11:05 AM (36 minutes ago)
Good morning Mr. Gander
Firstly let me introduce myself and my job function to you, I hold the job/position title, Senior Firearms Technician, specialized Firearms Support Services Section (SFSS). My section is a component of the Firearms Investigative and Enforcement Directorate, RCMP, Canadian Firearms Program.
This message is to confirm that the physical inspection of the Bren Gun Model Mark I serial number B417x is completed.
The following list of modifications from full automatic to semi-automatic have been observed;
List of Conversion (current);
1- The sear has been altered to remove full automatic capability by grinding off the automatic sear engagement surface of the sear.
2- The sear bent grounded off.
3- A pin was installed to obstruct the selector from pivoting into the full automatic position. This pin was welded to the interior oft he trigger frame assembly.
4- A hole was drilled through the sear pin and into the trigger frame; a roll pin was inserted to prevent the sear pin from being removed and prevent the sear from being replaced with an unmodified full automatic sear. (This method is not permanent and is addressed below in the upgrades required).
The above list of conversion is good but lack permanency. It is necessary that the alterations to the firearm to produce semi automatic fire is more comprehensive than simple disassembly and removal of full automatic parts or components which may easily and readily be replaced.
Updates required:
1- The trigger frame must be modified in such manner that it is no longer capable of accepting automatic parts;
a) The sear must be held permanently in place by the sear pin welded to the trigger frame at one or both ends.
b) The trigger pin must be welded into place at one or both ends to prevent the tripping lever from being replaced with an unmodified full automatic version.
Two options are possible at this point;
1- We can transfer the firearm to a local gunsmith here in Ottawa who can perform this type of work on this class of firearm, there is no cost to you for the transfer of the firearm to the business. However, any cost involved with the work on the additional modifications must be discussed/agreed between you and the gunsmith. The RCMP/Firearms Program is not responsible for any cost associated with this exercise.
2- We can return the firearm to you or to a properly licenced business of your choice who can perform the requested work. Again, any cost associated with the work being done is your responsibility. If the firearm will be returned to you it will be up to you to obtain the appropriate transportation permit (ATT) from your home to the prospective business or the carrier office. We can also return the firearm directly to the prospective business of your choice. The business has to be licenced to perform gunsmithing work on this class of firearm on behalf of a properly licenced individual (you).
I will provide the business with the instruction on the required work to be done. Once the requested modifications are completed, photos of the completed work must be submitted to me electronically for final approval. The final (updated) list of modifications will then be added to the firearm historical information and the transfer approved.
Please provide your preferred option.
Best regards
Daniel Guay
Senior FirearmsTechnician
I am guessing it will take a week and $100 to get these mods done and am pleased they will accept pictures of the work as proof.
Today I got this email:
Daniel Guay <Daniel.Guay@rcmp-grc.gc.ca>
11:05 AM (36 minutes ago)
Good morning Mr. Gander
Firstly let me introduce myself and my job function to you, I hold the job/position title, Senior Firearms Technician, specialized Firearms Support Services Section (SFSS). My section is a component of the Firearms Investigative and Enforcement Directorate, RCMP, Canadian Firearms Program.
This message is to confirm that the physical inspection of the Bren Gun Model Mark I serial number B417x is completed.
The following list of modifications from full automatic to semi-automatic have been observed;
List of Conversion (current);
1- The sear has been altered to remove full automatic capability by grinding off the automatic sear engagement surface of the sear.
2- The sear bent grounded off.
3- A pin was installed to obstruct the selector from pivoting into the full automatic position. This pin was welded to the interior oft he trigger frame assembly.
4- A hole was drilled through the sear pin and into the trigger frame; a roll pin was inserted to prevent the sear pin from being removed and prevent the sear from being replaced with an unmodified full automatic sear. (This method is not permanent and is addressed below in the upgrades required).
The above list of conversion is good but lack permanency. It is necessary that the alterations to the firearm to produce semi automatic fire is more comprehensive than simple disassembly and removal of full automatic parts or components which may easily and readily be replaced.
Updates required:
1- The trigger frame must be modified in such manner that it is no longer capable of accepting automatic parts;
a) The sear must be held permanently in place by the sear pin welded to the trigger frame at one or both ends.
b) The trigger pin must be welded into place at one or both ends to prevent the tripping lever from being replaced with an unmodified full automatic version.
Two options are possible at this point;
1- We can transfer the firearm to a local gunsmith here in Ottawa who can perform this type of work on this class of firearm, there is no cost to you for the transfer of the firearm to the business. However, any cost involved with the work on the additional modifications must be discussed/agreed between you and the gunsmith. The RCMP/Firearms Program is not responsible for any cost associated with this exercise.
2- We can return the firearm to you or to a properly licenced business of your choice who can perform the requested work. Again, any cost associated with the work being done is your responsibility. If the firearm will be returned to you it will be up to you to obtain the appropriate transportation permit (ATT) from your home to the prospective business or the carrier office. We can also return the firearm directly to the prospective business of your choice. The business has to be licenced to perform gunsmithing work on this class of firearm on behalf of a properly licenced individual (you).
I will provide the business with the instruction on the required work to be done. Once the requested modifications are completed, photos of the completed work must be submitted to me electronically for final approval. The final (updated) list of modifications will then be added to the firearm historical information and the transfer approved.
Please provide your preferred option.
Best regards
Daniel Guay
Senior FirearmsTechnician
I am guessing it will take a week and $100 to get these mods done and am pleased they will accept pictures of the work as proof.
