Cooey 75
- Thread starter jigger08
- Start date
Brownells offer a 12 inch blank 3/8 inch dovetail mount to fit a round reciever. A piece of this can be used and two holes drilled tapped into the top of the receiver and a scope mounted directly on top. It looks good and works well. Any gunsmith should be able to do the job. It is nicer than the side mounted base.
gunrunner100
CGN Ultra frequent flyer
- Location
- NW Ontario
I think the side base (Weaver) is a #2.
fat tony
CGN Ultra frequent flyer
I bought one of these recently, it needs a ton of work to get in order, that's okay though. Was thinking about the brownell's scope mount too, will that make the loading port hard to get at? What's the bbl length on your 75, jigger08?
by the way, here's info from Brownells about ordering parts
Currently we are holding your order. The order contains items the US Commerce Depart-ment regulates under the Export Administration Regulations. Brownells will need to ap-ply to the Commerce Department for a license in order to ship this order to you.
We will need an import permit from your country and a written order from you before we can make this application. You will need to mail these documents to us; our Commerce Department will not accept fax copies.
The combination of your country of residence or delivery and Shotgun parts (ECCN: 0A984), Sighting device (ECCN: 0A987) and/or other Non-specific gun parts (ECCN: 0A018) is the reason for this Commerce Department license requirement. The attached order marks the products in question.
Code references on the We
Commerce Department ECCN listings.
Shotgun parts 0A984
Sighting Devices and parts¹ 0A987
Non-specific gun parts² 0A018
¹ These are scopes, rings and bases
² These are “items on the Wassaanar List”
http://w3.access.gpo.gov/bis/ear/pdf/ccl0.pdf
Commerce Department Country Chart
Columns CC1, CC2, CC3, FC, NS1 and NS2 mean you need a license
http://w3.access.gpo.gov/bis/ear/pdf/ccl0.pdf
http://www.cfc-ccaf.gc.ca/compliance/bulletins/businesses/bulletin-16_e.asp
http://www.dfait-maeci.gc.ca/eicb/military/faq-en.asp
by the way, here's info from Brownells about ordering parts
Currently we are holding your order. The order contains items the US Commerce Depart-ment regulates under the Export Administration Regulations. Brownells will need to ap-ply to the Commerce Department for a license in order to ship this order to you.
We will need an import permit from your country and a written order from you before we can make this application. You will need to mail these documents to us; our Commerce Department will not accept fax copies.
The combination of your country of residence or delivery and Shotgun parts (ECCN: 0A984), Sighting device (ECCN: 0A987) and/or other Non-specific gun parts (ECCN: 0A018) is the reason for this Commerce Department license requirement. The attached order marks the products in question.
Code references on the We
Commerce Department ECCN listings.
Shotgun parts 0A984
Sighting Devices and parts¹ 0A987
Non-specific gun parts² 0A018
¹ These are scopes, rings and bases
² These are “items on the Wassaanar List”
http://w3.access.gpo.gov/bis/ear/pdf/ccl0.pdf
Commerce Department Country Chart
Columns CC1, CC2, CC3, FC, NS1 and NS2 mean you need a license
http://w3.access.gpo.gov/bis/ear/pdf/ccl0.pdf
http://www.cfc-ccaf.gc.ca/compliance/bulletins/businesses/bulletin-16_e.asp
http://www.dfait-maeci.gc.ca/eicb/military/faq-en.asp
Last edited:
jigger08 said:
Yup. What works great, since the receiver is so short, is to put one base on the receiver, and one on the barrel. I forget what number of Weaver base it is, but use same one on the barrel with a spacer the thickness to match the receiver. Of course you have to drill and tap for these.
