cowboy action revolver question
- Thread starter Dsiwy
- Start date
fingers284
CGN Ultra frequent flyer
- Location
- Alberta Cowboy Ranges
You will need two. They don't have to match as in maker or model or caliber but it simplifies thing if they do.
If you show up to a match with one and make it known that you only have one, I'll bet money that it won't be long before you are offered another to use or share for the match.
If you show up to a match with one and make it known that you only have one, I'll bet money that it won't be long before you are offered another to use or share for the match.
If you really like CAS, go online and read the SASS Shooters Handbook. Not all clubs are SASS affiliated but most do pay lip service to their safety requirements and period equipment. The Handbook also lists which firearms are appropriate for different categories. No use spending your money twice, when you can get it correct the first time!
Technically you COULD shuck and reload for the additional 5 rounds on the clock. But I know for sure that you'd instantly have at least three other folks on your posse offering to let you use one of their revolvers chambered in the same size ammo.
This will certainly get you through a few monthly matches in fine form. But eventually you'll be taking a lot of ribbing about it being time to buy a second revolver. But as long as you don't overstay the welcome they won't leave you high and dry.
This will certainly get you through a few monthly matches in fine form. But eventually you'll be taking a lot of ribbing about it being time to buy a second revolver. But as long as you don't overstay the welcome they won't leave you high and dry.
fingers284
CGN Ultra frequent flyer
- Location
- Alberta Cowboy Ranges
Our club, The Ottawa Valley Marauders has had folks with one SAA want to join us for some fun.
We welcomed them and allowed them to shoot. We just put them in a different category when scoring; "Working Cowboy" if I recall correctly.
It didn't take too long for them to obtain a second revolver after being loaned a number different SAA's to try while shooting full stages.
We welcomed them and allowed them to shoot. We just put them in a different category when scoring; "Working Cowboy" if I recall correctly.
It didn't take too long for them to obtain a second revolver after being loaned a number different SAA's to try while shooting full stages.
Dexter Morgan
CGN Ultra frequent flyer
Marstar has a ton of Pietta cowboy guns in stock, if anyone is looking for one.
http://www.marstar.ca/dynamic/category.jsp?catid=76374
You can get a pair of matching guns for under a grand.
http://www.marstar.ca/dynamic/category.jsp?catid=76374
You can get a pair of matching guns for under a grand.
I'm unsure, but I think we are.
What kind of cowboy guns do you have and what calibre?
I, or someone else, may be able to loan you what you lack, to get you through the stages.
Basically, you need a single action, a pistol calibre rifle and a shotgun with extractors, not ejectors and a cowboy type hat and some jeans to start, although cowboy boots and all the other accoutrements are eventually needed if you are getting into it the way many of us are.
Add another Ruger New Vaquero with a matching 5.5" and you are fully equipped. I'd also suggest swapping out the stock lever spring in your Stoeger for a lighter one. Will make opening and closing the action much easier. Also, since the Stoeger stock firing pins have a tendency to dub over and stick with heavy use.... common in CAS....causing misfires....replace the stock firing pins with stainless steel ones. Replacement lever springs and firing pins are available through the Longhunter site. Later on, as you become more proficient and wish to move up in the competitive ranks, you may also wish to replace the stock springs and hammers in your Vaqueros with lighter ones, too. These modifications will allow you to run your revolvers considerably faster than in stock configuration. Wolff springs are excellent. Plus available in a variety of weights. For hammer replacement, a pair of Ruger, New Model Super Blackhawk hammers will lower the hammer profiles considerably over the stock Vaquero ones, and allow for much quicker and easier cocking of the revolvers. These can be hard to come by in Canada. But, Numrich Gun Parts in the US, is a good source. The Miroku-made '92's are of excellent quality and run smoothly, right out of the box. Down the road, you may wish to acquire a second backup rifle. Also a second shotgun, and possibly a third revolver. Firearms , like any other mechanical object, can fail.....usually right in the middle of a match. So it is a good idea to have a spare on hand. As you gain more experience, you will see the need for spares.
If you haven't already done so, attend a couple of cowboy action matches. See what the other competitors are using. Talk to lots of people and ask lots of questions. Cowboys and cowgirls are the friendliest, most helpful folks you will find. Hope this is helpful.
If you haven't already done so, attend a couple of cowboy action matches. See what the other competitors are using. Talk to lots of people and ask lots of questions. Cowboys and cowgirls are the friendliest, most helpful folks you will find. Hope this is helpful.
There is a CAS group at Eganville DSC...if you are at the guns show this weekend ask about it.
Weapontech
CGN frequent flyer
- Location
- On my way to Hell in a handbasket
FYI.....
I have a beautiful matched pair of 1873 Cattlemans' from Uberti in .357 / .38 spl. Same serial numbers w/L & R prefix's) Brand new, unfired still in their boxs.
They're going on the EE in a couple of days - Save some $$.
Edit: I'm pretty sure a pair of these would be cheaper than 1 Ruger Vaquero in SS.
Last edited:
