In this thread, we discuss the Chiappa Alaskan Scout rifles.

K

kagia

CGN Ultra frequent flyer
Rating - 100%
48   0   0
Location
BC
I did a search and it didn't turn up any results on the Alaskan Scout rifles, so this will be a thread for any discussion related to these rifles.

Mods, accessories, issues, ammo, etc.

I just pulled the trigger on the 12" takedown model in .44 magnum. I'm really not sure why, considering I already have a Ranch Hand in the same caliber that I rarely use, but whatever. You know how it is...

Anyway, it probably won't arrive for a couple days, but I do already have a couple questions for anyone who already owns one.

How do you carry yours? I'd like to attach a sling, but there doesn't seem to be any factory attachment points. I do have a Voodoo Tactical (I think) scabbard that fits the Ranch Hand like a glove, but I'm not crazy about carrying it like that, and I don't really care much for the mare's leg type holsters either.

I'd also like a padded soft case for transport. Something nice and small. Barely big enough to fit the gun when it's broken down. What are you using?

Has anyone put a flashlight on theirs yet? That's the only real accessory I'd like to add to mine. And maybe one of them leather thingies that goes around the stock and holds a few extra rounds.
 
Last edited:
Hi there,

I have the .44mag 20"bbl version. Just got a Skinner Scout scope rail and a Leupold 1.5-5x33 VXR Scout Scope for it (Need some quick release rings)

Need to get some rings and a way of slinging it. There are some no-drill slings available it seems (google is your friend).
Skinner seem to make a case for it: http://www.skinnersights.com/scabbards_20.html

Think that case looks good and might get one...
 
I'm using a 24" tripod bag for my takedown Timberwolf.

HKVbZLYl.jpg
 
I have the ridge runner. I think it’s basically the same thing but in 45-70. It came with sling swivels, I’d be surprised if the Alaskan didn’t as well. Being a takedown I prefer a hard case to keep the parts from bashing into each other. I use a dewalt tough system case with some foam installed and the dividers removed, it just barely fits taken down. The lid has a storage compartment I keep a box of ammo and a flashlight in. It’s kind of big and bulky but doesn’t really look like it would have a rifle in it which I kind of like. Attaching a flashlight could be tough but you could screw a rail onto the forend?
 
Uisge said:
I have the ridge runner. I think it’s basically the same thing but in 45-70. It came with sling swivels, I’d be surprised if the Alaskan didn’t as well. Being a takedown I prefer a hard case to keep the parts from bashing into each other. I use a dewalt tough system case with some foam installed and the dividers removed, it just barely fits taken down. The lid has a storage compartment I keep a box of ammo and a flashlight in. It’s kind of big and bulky but doesn’t really look like it would have a rifle in it which I kind of like. Attaching a flashlight could be tough but you could screw a rail onto the forend?
Click to expand...

Afraid not eyes
 
I got a Skinner case for my Browning SA-22. Padded, securely closes up with buckles and straps, and has a couple of accessory pouches. I'm kind of interested in one of these Chiappa rifles, possibly in .357.





 
Thanks. Those skinner bags look pretty good. I may have to get one, but I think would rather have something with a zipper. I work and play in dusty environments and would like something that does a good job of keeping dust out.
 
Just picked up a 12inch Alaskan 357 take-down. Boy this thing is everything I wanted. Its smooth and light and well made.

I`m having a bit of an issue sighting in though...

Now I know this thing is made for close range, as the front hi viz front sight insert itself practically covers the entire 17x12 paper at 100 yards but centering on the whole paper gave me roughly 5-7inch groups benched which I think isn`t bad...

But I noticed that with elevation, I could half turn the ghost ring and hit either about 3inches high, or 3 inches low at 100yards roughly, there`s no in between....a 6inch elevation spread per half turn of the ghost ring at 100.

Again, the sight isn`t setup for long range accuracy and I`m aware, but am I just expecting too much? I have an 1894c that I can easily put inside 3-4inches at 100yards but thats with a 2.5x
I would expect a 357 carbine to be able to hit 100yards without issue.

Perhaps this close range ghost ring is just being finnicky and throwing me off and I`m expecting them to do more than they are made to do? Tell me I`m a bad shot, I can take it.

What are you guys setting up your zero at with the elevation that can`t 0 at 100?
 
Chuck3436 said:
Just picked up a 12inch Alaskan 357 take-down. Boy this thing is everything I wanted. Its smooth and light and well made.

I`m having a bit of an issue sighting in though...

Now I know this thing is made for close range, as the front hi viz front sight insert itself practically covers the entire 17x12 paper at 100 yards but centering on the whole paper gave me roughly 5-7inch groups benched which I think isn`t bad...

But I noticed that with elevation, I could half turn the ghost ring and hit either about 3inches high, or 3 inches low at 100yards roughly, there`s no in between....a 6inch elevation spread per half turn of the ghost ring at 100.

Again, the sight isn`t setup for long range accuracy and I`m aware, but am I just expecting too much? I have an 1894c that I can easily put inside 3-4inches at 100yards but thats with a 2.5x
I would expect a 357 carbine to be able to hit 100yards without issue.

Perhaps this close range ghost ring is just being finnicky and throwing me off and I`m expecting them to do more than they are made to do? Tell me I`m a bad shot, I can take it.

What are you guys setting up your zero at with the elevation that can`t 0 at 100?
Click to expand...

I don't expect my 44 Mare's Leg to be 100yd accurate. I get about 2 1/2" off the bench at 25 yds. 4-5"@50yds. A 12" barrel doesn't give you much of a sight radius. My 7 1/2" Blackhawk actually has better sights and shoots more accurately.
 
Chuck3436 said:
Just picked up a 12inch Alaskan 357 take-down. Boy this thing is everything I wanted. Its smooth and light and well made.

I`m having a bit of an issue sighting in though...

Now I know this thing is made for close range, as the front hi viz front sight insert itself practically covers the entire 17x12 paper at 100 yards but centering on the whole paper gave me roughly 5-7inch groups benched which I think isn`t bad...

But I noticed that with elevation, I could half turn the ghost ring and hit either about 3inches high, or 3 inches low at 100yards roughly, there`s no in between....a 6inch elevation spread per half turn of the ghost ring at 100.

Again, the sight isn`t setup for long range accuracy and I`m aware, but am I just expecting too much? I have an 1894c that I can easily put inside 3-4inches at 100yards but thats with a 2.5x
I would expect a 357 carbine to be able to hit 100yards without issue.

Perhaps this close range ghost ring is just being finnicky and throwing me off and I`m expecting them to do more than they are made to do? Tell me I`m a bad shot, I can take it.

What are you guys setting up your zero at with the elevation that can`t 0 at 100?
Click to expand...

The way it's set up, I think you may be asking a bit much of it. Smaller, more precise front sight and maybe a bolt mounted rear sight may help. With the takedown feature, it may not quite hold zero if you mount a rear sight on the bolt though.
 
Last edited:
2nd question, anyone recommend a sight tool for these skinner sights?

I DETEST trying to fudge an inch to the left/right with a punch and hammer!

I'm pretty close to bang on now but I might just zero off at 50 and call it a day. If I think of it as a mares leg with a stock I expect less than thinking its a 357 carbine with a short barrel...
 
CX Bike, sweet looking case that!

I'm wondering about adding a .22lr semi to the stable myself as I don't currently have a semi auto of any form.

(Also, my .22lr Brno model 2 is in a Boyd's Varmint Hunter stock. Very stable but not exactly light and packable...)
 
How is the build quality on these guns?
Functions well?
Fit and finish?
Looking at a 16 inch 357 but not willing to order until I know if they are good or not. Especially at this price point.
 
Fit and finish are excellent.

Its a solid carbine. I was actually surprised how smooth it was right out of the box.

It isn't cheap, but for the features that Wanstalls custom ordered on these Alaskans...stainless, octagon barrel, skinner sights, take-down, custom run for 357 magnum, custom run 12" barrels....

It actually isn't that bad.
 
You must log in or register to reply here.
Back
Top Bottom