Krinker kit allows any ak furnature?!

BBq_Woa!

BBq_Woa!

CGN Ultra frequent flyer
Rating - 95.3%
61   3   0
Location
Hamilton, ON, Canada
HI THAR.
while perusing krinker photos to drool over before I get mine, I saw this one from a thread by skirsons,
his beautiful 10/22 here
78567251.jpg


is shown, with wood furnature,
and later in the thread he says it "has a krinker kit on it, which allows one to attach ak furnature" (paraphrased)

is this true? is the krinker kit base able to accept all AK furnature??!

that's friggin amazing if so.

once I have mine I'll keep eyes open for some wood hand grip and forewood...

illllll

can someone clarify if this is true?
THANKS!
-Derek
 
If I remember correctly, SKS upper handguards are used for the upper wood and have to be trimmed, AK furniture for the rest. Not sure how attaching the butt works though, but I have seen krinkers with all AK/SKS wood.
 
Yes, I never attached the buttstock. I'm not sure how that would work either although I've seen it. The lower handguard and pistol grip require no fitting to attach, but the upper handguard is a hollowed out SKS handguard.
 
here's mine. the upper handguard can be fit with a few modifications. same thing for the stock. i had to make a part that bolts to the stock, then bolts to the gun.
DSCF0611.jpg

DSCF0612.jpg
 
i just copied the part from the folding stock that bolts to the receiver. its made out of 12 gage steel plate and welded together. On the left side there is a gap for the folder hinge that i filled with jb weld and then sanded. the pictures can explain it better than i can.
DSCF0613.jpg

DSCF0614.jpg

DSCF0615.jpg

heres some close-ups of the upper handguard
DSCF0616.jpg

DSCF0617.jpg

DSCF0618.jpg
 
Here's the steps in a little more detail.

This is the handguard cap that comes in the krinker kit. I had to extend it with the piece that was on the ak guard. I used JB weld
DSCF0768.jpg

Same thing here. This is the original upper handguard with the piece from the back of the ak handguard attatched. JB weld here as well.
DSCF0770.jpg

The front of the upper wood has to be trimmed like so.
DSCF0771.jpg

DSCF0772.jpg

Thats pretty much it for the front of the gun. The lower guard fits right in no problem. (might have to sand it a little)


This is the stock adaptor I made. I just copied the one attatched to the folder minus the hinge. Threads are 8-32. It is attatched to the stock with a 1/4" lag bolt and a screw on top.
DSCF0774.jpg

There is a cutout in the receiver for the hinge so with this new piece there will be a gap. I filled and then shaped it with JB weld
DSCF0775.jpg

DSCF0776.jpg

DSCF0777.jpg

The upper handguard assembly fits pretty tight so I have to put it back together in this order.
DSCF0778.jpg

DSCF0779.jpg

DSCF0780.jpg

The pistol grip had to be dremeled out so the trigger guard can sit back where its supposed to be. Just copy the krinker grip.
DSCF0782.jpg


Thats it.
 
Buddy thank you so much for your help. it was an amazing amount of help... and i have a couple people that messaged me with ak wooden furniture, so this build looks very possible.

Cheers everyone.


Rob

will post pics of my build aswell
 
DKS said:
here's mine. the upper handguard can be fit with a few modifications. same thing for the stock. i had to make a part that bolts to the stock, then bolts to the gun.
DSCF0611.jpg

DSCF0612.jpg
Click to expand...

What kind of mag is this one ??? It is not regular ButlerCreeck ? It is flat one and I like it :) Where I can get couple of tehse ones ? How many rounds in it - 25 or 30 ?

Thank you ;)
 
You must log in or register to reply here.
Back
Top Bottom