Multi Cam level 3 Vests With Side Protection and Mag Pouches.

[Frontier Firearms]

The vests are GX Xinxing, it’s an Airsoft quality vest... can be had on amazon for $70 shipped next day.
The plates were listed at $80 each for the full size plate but seem to no longer be listed and probably sold out.
Add a few bucks for the smaller side plates and at the very most these sets should be well under $300.
For $370 + tax I expected a bit more from the carrier. Cheap plates are cheap plates and I was planning on replacing them with quality plates but the carrier is going to my kids for airsoft.

You are correct to a point, the plates "were" $80 each. Just like SKS rifles were $199.95, K31s were $295 at one time. There were $80 before and slightly after Christmas because we had several pallets of them that we paid a very low price on. Thats why we could sell them for $80 instead of $130 that they would normally sell for. Fastforward 4 weeks later and we are buying plates a few dozen as we found them vs 2 pallets at a time. As for "a few bucks" for the side plates, try $30 and add 15-20 mins to cut them properly. If you dont like the quality, you can always step up to AR500 plates and a miltec laser carrier for $700.

Feel free to post a link on here showing all of the options in Canada for a set up that will stop 308 & 7.62x39 FMJ for under $300.

 

[climbingrocks]

... add 15-20 mins to cut them properly...

What did you use to cut these plates? Could you do it with a hand saw or is a band saw required? Thank you.

 

[Frontier Firearms]

It is a special grinder blade that seals them as they cut. First time we tried this with a saw it was not good, the edges looked like a sheep dog. The material frays and then will not cut straight.

 

[somethingspecial]

It is a special grinder blade that seals them as they cut. First time we tried this with a saw it was not good, the edges looked like a sheep dog. The material frays and then will not cut straight.

Details on the grinder blade would be appreciated.

 

[rubberdonuts]

Details on the grinder blade would be appreciated.

Or please allow a service to cut them for us.

 

[Dlask Arms]

Or please allow a service to cut them for us.

Yes please. These large side plate don't fit any carrier I have but they *could* if you cut them for us lol....

 

[Fyn]

I used a die grinder and cut off wheel. Made a pretty clean edge, a higher speed wheel seems to cut and melt the plastic/Polymer but still get through the fibers cleanly.

Was going to buy one of the side plates and cut it and do some testing to see if cutting it affected the integrity much, but they're all sold out now.

 

[Vewdu]

I used a die grinder and cut off wheel. Made a pretty clean edge, a higher speed wheel seems to cut and melt the plastic/Polymer but still get through the fibers cleanly.

Was going to buy one of the side plates and cut it and do some testing to see if cutting it affected the integrity much, but they're all sold out now.

A zipcut is all you need.

 

[Yehen]

Any more of these vests coming in by chance?

 

[Brooker1]

anymore of these carriers coming in?

 

[dfemia01]

Tagged

 

[Frontier Firearms]

We have added some more of the Level 3 Vests from a Previous Thread. These will start shipping next week. They are a bit different than last time.




We also have some level 3A soft armor vests available this week. These use 2 panels from Italian Surplus vests in level 3A.

 

[Gnome75]

Are you guys selling the italian plates on their own?

 

[Frontier Firearms]

No, we do not have enough right now.

 

[Frontier Firearms]

We are able to get only enough plates for 3 vests per week. New shipments will not have the small side protection plates. 3 of these will be ready to ship a week from today.




A few of these ready to ship.

 

[Frontier Firearms]

2 of these back in stock.