Quality rings that will mount onto a CZ 11mm dovetail?
- Thread starter CanuckShooter
- Start date
- Location
- Quebec city
Warne 721 or 722 are solid.
Leupold.....I'm thinking even some Burris rings as well.
* I do not know the part number with an advanced apology for that.
But, the search will be so much better when you find either set.
Rob
D3 brand rings are a relatively recent addition to rings that are made fit CZ 452, 455, and 457 receivers, both 3/8" and 11mm, as well as Anschutz. They are available in 3/8" and 11mm. Shown immediately below are rings that fit thee 3/8" dovetails on a CZ 452 American. These are available on ebay, perhaps elsewhere too. h t t p s://www.ebay.com/itm/Scope-Rings-11mm-and-3-8-Dovetail-fit-Anschutz-CZ-452-455-457-1-30mm/264268435836?hash=item3d87a0517c:g:u6cAAOSwF3Vc2xkf
I will be considering these if I ever need more rings.
I will be considering these if I ever need more rings.
A lot of the air rifles are metric based and have an 11mm dovetail. Below are a couple of the Canadian dealers. Amazon is another source. Sportsmatch, BKL, FX, Eagle Vision are some of the better mounts. You can also buy 11mm dovetail to Picatinny adapters.
https://www.airgunsource.ca/us/scope-optics/scope-mounts/
https://dlairgun.com/collections/bkl-mounts
https://www.airgunsource.ca/us/scope-optics/scope-mounts/
https://dlairgun.com/collections/bkl-mounts
Last edited:
CanuckShooter
CGN frequent flyer
Man, I had no idea there were so many options now, a it's been ages since I scoped a CZ. This is great. Bookmarked and am looking into all of the suggestions.
I just checked these out. Nice looking rings. What's the difference between the 721 and 722 though? Is it just that one is high and the other is medium?
I know the BKL 200's well as I used them on a couple CZ rimfires in the past, but they're hard to get these days. I'm trying the find out if the Burris Signature rimfire rings are designed to fit both 3/8" and 11mm dovertail but it doesn't say on their site. Any idea?
Thanks again
I just checked these out. Nice looking rings. What's the difference between the 721 and 722 though? Is it just that one is high and the other is medium?
I know the BKL 200's well as I used them on a couple CZ rimfires in the past, but they're hard to get these days. I'm trying the find out if the Burris Signature rimfire rings are designed to fit both 3/8" and 11mm dovertail but it doesn't say on their site. Any idea?
Thanks again
Last edited:
Rod B
CGN Ultra frequent flyer
Yes they fit both 3/8 & 11mm.
Last edited:
721 is medium and 722 is high for the Warnes. The Warnes rings can be used on 3/8" and 11 mm dovetails. They have a reversible claw on the bottom for either dovetail specs. Factory set to 3/8" as indicated by a dimple in the reversible claw. I've got the QD rings on the kids rifle because that's what I could find. However, there is no positive stop for the rings in the receiver grooves to get an accurate remount I you decide to take the scope off.
Airgun source has a bunch of options.
I have been using pic rail rings with a dovetail adapter.
If you are a long range guy you will like the adjustable height models so you can set the slope you want rather than guess at it with a 20 30 or 40 MOA base.
I have been using pic rail rings with a dovetail adapter.
If you are a long range guy you will like the adjustable height models so you can set the slope you want rather than guess at it with a 20 30 or 40 MOA base.
Leupold cz/rimfire rings Medium height they come in gloss blued. Or matte. Gives just enough clearance for the newer 455 bolt handles with the hole in the ball. The polished blued bolt handles with no hole are a bit thicker where it could come into contact with the eye piece of the scope. But if its a newer 455 with the flat black handle with the hole in the ball, Part number 54231 is what you want to have just enough clearance for the bolt handle, and a low enough hight over bore for the scope to have a good cheek weld. The leupold high cz/ rinfire rings part number 54234 are too high to get a good cheek weld on an American stock without an extra cheek riser. Just my opinion.
