reloading room/junk cave

[Cocked&Locked]

Just a few pics of where i end up hiding during the weekends.

and then my batteries died, lol, the bigger locker is behind me, adn you don't get the full clutter effect. I am so envious of a certian someone building in a refurbed cistern!

 

[grijim]

Well you picked a hell of a sweet place to hide out.

Grijim

 

[acrashb]

Looking good - although there should be a new gun on display somewhere

 

[fogducker]

Looking good - although there should be a new gun on display somewhere

ya...................... and a brass tumbler

 

[broncoo]

ill have mine setup just as soon as i build my 16x8' shed in the backyard got all the yardwork stuff cluttering my gun room and part of my workshop

 

[MudChucker]

if your spending your time in there on the weekends, when do you get a chance to make more brass to load ?

 

[Fall Guy]

Is that C-clamp to holding down that powder measure?

 

[Cocked&Locked]

Is that C-clamp to holding down that powder measure?

yep, lets me move it around.

and foggy, i just landed a sweet motor drive, so somehow i'm up to between 2 and 3 sets of motor and drive, want to go into series production ? lol

 

[fogducker]

yep, lets me move it around.

and foggy, i just landed a sweet motor drive, so somehow i'm up to between 2 and 3 sets of motor and drive, want to go into series production ? lol

do any of the motors come with a speed control?..
also work on some bearings that will accommodate a shaft of lets say 3/4 dia.... the inside dia. of the bearings can be a bit smaller,as we can machine the ends of shaft down a bit..

 

[7.62mm]

Is that C-clamp to holding down that powder measure?

I am sure a person could find one bigger than that......although I am not sure where......LOL!!!!

 

[Onagoth]

Where do you get that roll handle for your LNL AP?

 

[Cocked&Locked]

do any of the motors come with a speed control?..
also work on some bearings that will accommodate a shaft of lets say 3/4 dia.... the inside dia. of the bearings can be a bit smaller,as we can machine the ends of shaft down a bit..

all three

 

[Cocked&Locked]

Where do you get that roll handle for your LNL AP?

I made it, turned out of delrin and bearings rotate on a shoulder bolt. If i did it again i'd have set it more of a D handle, mounted in the center.

 

[Cocked&Locked]

I am sure a person could find one bigger than that......although I am not sure where......LOL!!!!

I'm bad at picking up what i have and using it, instead of walking accros the shop to get a smaller one. It also holds down my case trimmer if i'm doing that, and a few other odds and ends. It's big enought to let me move stuff around on the bench.

 

[fogducker]

all three

THREE.............
you should change your name from Cocked& Locked
to
Horseshoes up Arse...
get some bearings and give me a ding

 

[Fall Guy]

I'm bad at picking up what i have and using it, instead of walking accros the shop to get a smaller one. It also holds down my case trimmer if i'm doing that, and a few other odds and ends. It's big enought to let me move stuff around on the bench.

I mounted mine on a 3/4" plywood base to increase the foot print which resulted in balancing the measure. It has never fallen over.

 

[kjohn]

C&L: What kind of press is that?

 

[Cocked&Locked]

Its a (very?) old Lyman all american. 4 stage turret press, got it from a friend who wasn't using it. Last time i was at epps they had one up there in the used section. Needs an adaptor to use modern shell holders, but lyman sells that, and i like the press. I'd prefer a redding T7, but this was free.