Remington VersaMax R12

[Yuri_Wolverine]

R12's have Just landed!

Looking for a sweet, superbly reliable, semi-auto, 18.5" 12 gauge?

Did I mention they are CHAMBERED FOR 5 3 1/2" SHELLS?

We have a few of the new Remington Versamax R12's in stock now!
Buy them here ----> https://www.wolverinesupplies.com/ProductDetail/REM82795C_-Remington-Defense-VERSA-MAX-R12-12ga-3-1-2--Synthetic-

 

[The Crover]

What's the 3.5" shell capacity?

 

[Wolverine Guy]

What's the 3.5" shell capacity?

5.....

 

[Helsinki Cowboy]

.......

 

[The Crover]

5.....

Is the magazine tube under the hamdguard one piece or is there a short magazine tube plus an extension?

 

[Yuri_Wolverine]

Pretty nice but other than the 3.5 inch shells what makes it better than my 11-87 Police ?

More reliable gas system, extended controls, and in my opinion the most interesting part, is the fact that i can load six 2 3/4 shells. With a little work a seventh could be made to fit with out violating the 5 round 3 1/2" capacity.

 

[Yuri_Wolverine]

Is the magazine tube under the hamdguard one piece or is there a short magazine tube plus an extension?

 

[PaveHammer]

Are the receivers drilled and tapped for optic mounts from the factory?

Any interest in bringing in the shorter variants?

Thanks,

Bradley

 

[The Crover]

So the tube is solid, but the barrel is made for a shorter one so they make you use that sleeve to shim the gap between the barrel ring and the magtube cap?

 

[call2arms]

Are the barrels special Canadian edition? Fixed choke?

 

[The Crover]

More reliable gas system, extended controls, and in my opinion the most interesting part, is the fact that i can load six 2 3/4 shells. With a little work a seventh could be made to fit with out violating the 5 round 3 1/2" capacity.

Have you tried putting 5 3.5" shells in the tube? If there is still room in the tube then you might not need to modify anything to get 7 2.75" shells in.

 

[Yuri_Wolverine]

Have you tried putting 5 3.5" shells in the tube? If there is still room in the tube then you might not need to modify anything to get 7 2.75" shells in.

I have, ts a tight 5. However with out the little plastic spring keeper at the end of the tube it can fit seven 2 3/4" as a point of reference. I wouldn't run the gun with out that as it has the ratchet teeth that keep the end cap on.

 

[The Crover]

I have, ts a tight 5. However with out the little plastic spring keeper at the end of the tube it can fit seven 2 3/4" as a point of reference. I wouldn't run the gun with out that as it has the ratchet teeth that keep the end cap on.

How big is the follower? Maybe a smaller one or a shorter spring would do it.

 

[Yuri_Wolverine]

Are the receivers drilled and tapped for optic mounts from the factory?

Any interest in bringing in the shorter variants?

Thanks,

Bradley

Yes they are drilled and tapped.

I doubt that we will see anything shorter than this. The US state department has really clamped down on export of shotgun barrels shorter than 18". Not sure why it be like it is but it do.

 

[Yuri_Wolverine]

Are the barrels special Canadian edition? Fixed choke?

They are non restricted with a 18.5" barrel. And they do have a fixed choke.

 

[Yuri_Wolverine]

How big is the follower? Maybe a smaller one or a shorter spring would do it.

That may work as well! Not too sure tbh.

 

[CTBaumhour]

The real question is, how many of the 1-3/4" mini shot shells does it fit? Double digits!?

 

[dacron]

5x3.5=17.5/1.75=10

 

[The Crover]

They are non restricted with a 18.5" barrel. And they do have a fixed choke.

Reliable has on their site these guns with a ProBore IC, are they different that yours? About the only thing keeping me from buying one is the fixed choke.

https://www.reliablegun.com/en/remi...table-stock-top-rail-anodizedpvd-black-finish

 

[Wolverine Guy]

Reliable has on their site these guns with a ProBore IC, are they different that yours? About the only thing keeping me from buying one is the fixed choke.

https://www.reliablegun.com/en/remi...table-stock-top-rail-anodizedpvd-black-finish

They are exactly the same SKU and from the same supplier. They have a fixed choke and are designated as the Canadian compliant model on the end of the box.