I need a 'reloading 101'

Sporting Lad

Regular
Rating - 100%
1   0   0
Location
Vancouver Island
I'd like to begin reloading my own ammo now, but I don't even know where to start.
I've been shooting for fifty years, but I've yet to reload a single round.
Is there some sort of "Reloading 101" reference I could use to help get me started?
thx
SL
 
I'd like to begin reloading my own ammo now, but I don't even know where to start.
I've been shooting for fifty years, but I've yet to reload a single round.
Is there some sort of "Reloading 101" reference I could use to help get me started?
thx
SL

You can start by picking up a copy of one of the many reloading manuals out there, ABC's of reloading is one, Lee has their own as well as Hodgdon I believe. If you google reloading manual am sure you will find more than a few.
Read read read, took me 3 months to read everything and understand it all. There are a lot of websites dedicated to reloading in the US, think ar-15.com has a section dedicated to it. Look out on the EE for all the bits and pieces you'll need to start, I recommend a cheap used single stage press like a Rockchucker or a Lee press(Though I have 2 RCBS Rockchuckers myself) can be had for under $150 on the Equipment Exchange (EE for short) if you are quick enough to see one before they sell.
I've been collecting equipment slowly myself for 7 years and have barely used most of it, as am waiting till I can afford a membership at a gun club before I really get into it, though I did reload with a good friend over 20 years ago and just had to refresh some of the info.
Read most of what the elder posters here have to say, BearHunter is one, Kamlooky, EagleEye, and if you want too much info(LOL) read up posts from biged51 - one of our American friends. Lots of knowledge here and if you have questions once you've read up don't be shy to ask here. Oh and just do the exact opposite of 98% of what Sunray says and you'll be just fine.
 
The ABCs of Reloading.

bingo

+ the lyman 49th edition and lee's reloading manual.


go through the last couple pages of the reloading forum, there has been several newbie reloading threads started with lots of info in them.

for visual learning youtube has lots of good videos from most of the bigger youtubers with good info and shows what kinds of tools are used.

my questions for beginners are 1. budget? 2. what are you wanting to reload? 3. what is the ammo to be used for?
 
youtube. Thats where I started, then forums (brianenos of Dillon etc). then I settled on a Dillon 650 and havent looked back. Have fun, its easier than it sounds. Lots of variables to sort through at first, but once you're set up, its straight forward.
 
+1 for YouTube it will walk you through the process step by step
After watchin a few videos you will know if it's for you or not
But read the manuals they hold a lot of information
 
Maybe one of these fine gents can invite you over and go through it with you.

It all seems a little overwhelming until you actually see it done.

Then go through the manuals and start learning all the nitty gritty stuff.
 
There was a thread started just a couple days ago on this exact topic. You may find some of the information useful:

hxxp://canadiangunnutz.com/forum/showthread.php/1232821-How-to-start-in-the-reloading-game
 
my questions for beginners are 1. budget? 2. what are you wanting to reload? 3. what is the ammo to be used for?

4. Approximately what quantities will you be shooting in a month/year?

The answer to this makes a big difference, IMO.

I'm just a rookie reloader, but with the minimal experience I have had so far, the one thing that I have noticed is that there is as much bad advice about reloading as there is good advice.

Note: I am not pointing any fingers. Just a general observation.
 
4. Approximately what quantities will you be shooting in a month/year?

The answer to this makes a big difference, IMO.

I'm just a rookie reloader, but with the minimal experience I have had so far, the one thing that I have noticed is that there is as much bad advice about reloading as there is good advice.

Note: I am not pointing any fingers. Just a general observation.

I knew I forgot a question! But that's what I got for staying up to late Haha.
 
I started 6 months ago. Got a RCBS rockchucker supreme kit, trimmer,Calipers,dies and a vibratory cleaner. I read the Speer manual ( well some of it) watched some you tube, asked some question on CGN. I started with .223 ,2250 and .308. I'm now also doing .45 LC,9MM and .357/38. It's not as difficult as it looks. I made a couple minor mistakes but that was sorted out quickly , thanks to the advice of CGN members. If I'm not sure of something, I just keep asking until someone explains it to me , in a way that I can understand :)
 
As I said before, I am just a rookie - so take this with a grain of salt:

I agree 100% with Brianma65. It is not as hard as it looks. If you remove all the machinery and gadgets, and just think about the components themselves, it is quite simple.

1) Brass - brass should:

a) be the correct brass for the cartridge
b) be in good condition (no cracks or other signs of fatigue)
c) be relatively clean (how clean it needs to be depends on both personal preference and reloading method)
- cleaning methods and equipment vary, from a jar with vinegar/water to various types of tumblers - you can spend as little or as much as you want here
d) have clean primer pockets - dirty primer pockets can prevent full seating of primers, which can be a safety issue
- cleaning primer pockets can be achieved in various ways - ingenuity can replace special tools of various cost and effectiveness
e) be the right size/length - brass that is too long will create a safety issue - brass that is too fat may not chamber in your firearm
- Some reloading methods only size the neck of the case - this is fine if you only intend to use the brass in a single firearm, and there is less wear on the brass
- the length of the brass should always be checked and, if required, trimmed to official cartridge specs - a quality caliper and trimming tools are a must - trimming tools range dramatically in price, but all do the same thing

2) Primers - primers should:

a) be the correct size/style for the case/cartridge being loaded
b) be fully seated in the primer pockets of the cases (see 1) d) )

3) Projectiles - projectiles should

a) be the correct caliber for the cartridge being loaded
b) be an appropriate weight and construction for the intended purpose
c) be seated in the case to appropriate C.O.A.L specs for the cartridge

4) Powder - powder should:

a) have burn rate and other properties appropriate for the cartridge and for the specific projectile weight and design
- manufactures of powder and projectiles publish this information
b) be measured accurately, according to proven, official load data
- equipment ranges from a plastic scoop (Lee "dipper"), through to scales/measures worth many hundred dollars


Regarding gear; all of the above can be achieved for as little as $150, or one can spend several thousand. That's all determined by how many rounds you want to shoot, and your budget.

Better (or more expensive) gear does not necessarily make safer or better reloads. Your full attention to detail is required no matter what.
 
Last edited:
Best advice (mentioned already)...do what you can to find someone locally who can show you. NOTHING takes away the mystery of reloading faster~wish I would have done it myself.

Instead, I bought a used vise... .223 dies ...decent dial calipers and various Lee hand tools to start prepping brass and build-up my confidence. YouTube videos helped immensely. Watched/read lots of powder-measure and digital powder scale online reviews...saved...and picked these up over the course of a few months. Other than upgrading the powder measure and a few dedicated/task-specific hand tools...my set-up is still the same..still very basic. I reload .223 and .204R, contemplating shotgun...but that's a whole different subject.
 
Well Sporting Lad, no one seemed to understand the gist of your question, which I take it as you wanting, as you said, a 101 course/read on reloading, and not hours and hours of reading huge manuals.
At the time you started shooting you could have had your choice of several 101 pamphlets of reloading.
The one I chose was the Norma Gunbugs Guide, a total of 25 pages, including all the rifle loading charts. Everything one needed to know on how to reload your rifle ammunition to very good efficiency and how to stay safe in doing it, was in that little reloading guide. When the huge manuals started coming out, I think in the 1970s, I never bothered to get one, thus the only real reloading manual I ever had was my little Norma Gunbug Guide.
You could also walk into any gun store and get a loading chart, showing loads, usually from powder manufacturers.
Every loading chart was the same, in that it showed the type of powder to use with various weight bullets in the various rifle calibres and the charge weight of the powder to use.
In short, they didn't state what type of primer to use, or the COAL, or any different powder charges for different bullet, just went by weights, or any starting loads of powder, but most of the charts stated you should start a little lighter and work up.
Once upon a time life was simple!
 
The ABCs of Reloading runs about $30 at your local gun shop or Amazon. Reloading is a long way from being rocket science. Isn't difficult to pick up from reading.
Then look into an RCBS beginner's kit. And buy a Lyman manual.
 
There ya go, it's not that hard, no need to read 4 , 800 page books. Get a manual for loading correct bullets and powder charges. Read the instructions that come with the dies ( they were the only issues I ha and they were easy to correct. Start with one caliber until you get the hang of it , and it gets easier. The hardest part I find now , is finding the right powder . But you'll find that if the powder is not listed , you can still make do sometimes. Also if you could find one person on here to guide you , it would be much better than having 10 different opinions thrown at ya. H4831 just have some of the best advice I've seen yet.
 
Back
Top Bottom