NEW CZ 858 Canadian Model

Status
Not open for further replies.
are they chrome line ?

just kidding i know they are not ,

maybe for the first 100 you should get them all chromed outside except the inside of the barrel

when they are finally for sale again i might as well grab a second one
 
slim123 said:
im getting tired of this "old" thread that keeps poppin up like new.....

btw grumpy, I sent an email to john asking him some direct questions about a order I want to put in...but there were website issues that I asked about....been a week now...still no reply
If you guys are too busy to answer emails inquiring about a "good size" order....then maybe you have too much business already and obviously don't need more....
In todays internet world its extremely easy to find another vendor.....a few seconds at the keyboard..
I like you guys ( and have gave you plenty of business in the past), but I stopped buying from wolverine a few years back due to very slow shipping.....

with November creeping up fast......theres no way ill wait 2 weeks or more for my order...when other vendors I have ordered from have the product out the door the same day...and I get it home 4 or 5 days after that...

Im not #####ing....just dissapointed
Click to expand...

Hmmm sounds like #####ing to me
 
870supermag said:
Iv just sent wolverine a email but is any one else aware of this so called just bend the spring fix for the gremlin??
Click to expand...

Not a "so called fix" it is a fix and it works well.
The "gremlin" is a condition that can result in the striker not being caught by the sear and following the carrier home, which ends up with the rifle being un-cocked.

The main cause, is that during the carrier assembly's rearward travel, the striker must push the sear back down to continue on it's path. If the sear is pushed down too far (as far as the trigger would move it), it misses the hook on the disconnector, allowing the hook to spring back up and stop the striker. Bending the disconnector spring up to put more pressure on the disconnector keeps everything in proper plane and stops the "missing of the hook".
A shooter can also cause the problem by partially letting go and re-pulling the trigger during recoil. It actually causes the issue to happen more often which explains why some people have more occurrences of the gremlin than others. Some rifles will never experience the gremlin as their disconnector spring is already tensioned. This fixed has been used many times and works very well. The completely permanent fix is to have the bolt carrier tabbed but it needn't be necessary unless it is something you wish to have done.
 
870supermag said:
Iv just sent wolverine a email but is any one else aware of this so called just bend the spring fix for the gremlin??
Click to expand...
It does work it's a quick fix. I found myself needing to retention my spring once or twice, i would say every 500-1000 round.... omg what a thing!!!!!!... weĺl it's a breeze and your cleaning your gun anyway. The only down side is a bit of a heavier trigger pull i think.
 
rally guy said:
It does work it's a quick fix. I found myself needing to retention my spring once or twice, i would say every 500-1000 round.... omg what a thing!!!!!!... weĺl it's a breeze and your cleaning your gun anyway. The only down side is a bit of a heavier trigger pull i think.
Click to expand...

I don't mean to thread jack but any chance you could post pictures of what exactly you're talking about? Any pictures that were linked to CGN seem to be down as it was from a few years ago. So are you just bending an existing spring or are you adding another spring?

Thanks
 
Red_Liner740 said:
Keep dreaming. No way will it be sub $800.
Click to expand...

Would you care to place a bet? :)

Shipment is delayed as the Czech authorities are insisting on an original of our import licence so I doubt we will see these before Christmas.

What I can tell you:

The First 300 will be a very special one only edition, never to be repeated, these will not be cheap!

Our intention (Remember the road to hell is paved with good intentions) is to start the basic model at $799, remember I said intention, this is not guaranteed as we have a lot of expenses apart from the exchange rate and we can not calculate them accurately at this time.

Quantities will be limited, certainly to start with.

No pre-orders and no notify list.

When we unload the pallets into our warehouse we will announce it and then we will accept orders in full.

Realistically I would expect these to arrive here around Christmas so we should be selling these after our Christmas break.

Thank you for your patience. remember I will have waited three years to see these rifles!
 
Red_Liner740 said:
Keep dreaming. No way will it be sub $800.
Click to expand...

Oh now aren't you just a Negative Nellie......
7595b906a311af46e97096438d2f3604.jpg
 
Mr Wolverine said:
Would you care to place a bet? :)

Shipment is delayed as the Czech authorities are insisting on an original of our import licence so I doubt we will see these before Christmas.

What I can tell you:

The First 300 will be a very special one only edition, never to be repeated, these will not be cheap!

Our intention (Remember the road to hell is paved with good intentions) is to start the basic model at $799, remember I said intention, this is not guaranteed as we have a lot of expenses apart from the exchange rate and we can not calculate them accurately at this time.

Quantities will be limited, certainly to start with.

No pre-orders and no notify list.

When we unload the pallets into our warehouse we will announce it and then we will accept orders in full.

Realistically I would expect these to arrive here around Christmas so we should be selling these after our Christmas break.

Thank you for your patience. remember I will have waited three years to see these rifles!
Click to expand...

John, this IS excellent news to hear and I am very excited and happy with what you have done for this community!!!!!
I will buy one for sure.

But one last thing, WTF is going on with the skorp Evo III??? :-(
 
But one last thing, WTF is going on with the skorp Evo III??? :-(

That is a very good question? This needs to be directed at our politicians who have allowed bureaucrats Policy to be implemented as law allowing the CFC and RCMP SFSS to have dictatorial powers. We are waiting for a classification from the RCMP SFSS.
 
Status
Not open for further replies.
Back
Top Bottom