Lets see some pics of your tactical shottys!
- Thread starter mmatt
- Start date
TV-PressPass
CGN Ultra frequent flyer
- Location
- Mountains, Alberta
I've taken my SAP-6 in a new direction...
Some facts:
Some facts:
- This is the 14" barrel. This one's got chokes (finally)
- The stock has to be JB welded permanently open in order to retain the NR overall length requirements.
- The mag coupler is an Israeli design that I "upsized" using seat belt strapping.
- In this setup you can carry 22 rounds of 12 gauge on the gun. I guess 23 if we're doing one in the pipe.
Benelli_Beginner
Member
- Location
- Dewinton, AB
I've taken my SAP-6 in a new direction...
Some facts:
- This is the 14" barrel. This one's got chokes (finally)
- The stock has to be JB welded permanently open in order to retain the NR overall length requirements.
- The mag coupler is an Israeli design that I "upsized" using seat belt strapping.
- In this setup you can carry 22 rounds of 12 gauge on the gun. I guess 23 if we're doing one in the pipe.
Now that is tacticool......
What stock is that?
Here's my Mossberg 500. It's an older model that I picked up for cheap from my brother in-law's late father's estate. Not quite finished with it yet but here's what I have done so far:
ATI Talon 6-position stock and forend
Tacstar 6 shell side saddle
Flashlight mag tube mount and 150 lumen light
Mag tube plug delete and spring replacement
Magpul MS3 Single/dual point sling
Receiver, mag tube and barrel painted flat desert tan (done with cheap Canadian Tire paint to see if I like it, I do. Plans to repaint with gunkote or similar)
Mods I'd like to do:
Sights (leaning towards ghost ring)
Possible barrel replacement
Laser sight to mount to front picatinny
Open to suggestions
ATI Talon 6-position stock and forend
Tacstar 6 shell side saddle
Flashlight mag tube mount and 150 lumen light
Mag tube plug delete and spring replacement
Magpul MS3 Single/dual point sling
Receiver, mag tube and barrel painted flat desert tan (done with cheap Canadian Tire paint to see if I like it, I do. Plans to repaint with gunkote or similar)
Mods I'd like to do:
Sights (leaning towards ghost ring)
Possible barrel replacement
Laser sight to mount to front picatinny
Open to suggestions
I've taken my SAP-6 in a new direction...
Some facts:
- This is the 14" barrel. This one's got chokes (finally)
- The stock has to be JB welded permanently open in order to retain the NR overall length requirements.
- The mag coupler is an Israeli design that I "upsized" using seat belt strapping.
- In this setup you can carry 22 rounds of 12 gauge on the gun. I guess 23 if we're doing one in the pipe.
I had a similar dual mag set up on my grizzly but found that rounds would pop out of the second mag do you have the same problem?
870 FDE Magpul Edition. Upgraded with:
-Big Speed Safety
-Volquartsen EDM extractor
-Anti-drift trigger pins
-Rem IC choke
-Brownells SS follower (to replace plastic follower), Vang Comp SS follower (to replace plastic spring retainer)
-All friction surfaces highly polished, chamber polished
-Big Speed Safety
-Volquartsen EDM extractor
-Anti-drift trigger pins
-Rem IC choke
-Brownells SS follower (to replace plastic follower), Vang Comp SS follower (to replace plastic spring retainer)
-All friction surfaces highly polished, chamber polished
All mods are internal. Carrier dog spring from an 1100, HD mag spring and delrin follower, HD extractor spring and contoured forged extractor. A chamber and inner receiver polish to continue the tweaking process.
I'm expecting again, soon I'll have another mag to feed
Last edited:
Maverick 88 Tactical
Mossberg Maverick 88 with ATI Ghost Ring Heat Shield, Millett Optic mount, Surefire Flashlight, Red Dot
[/url]Shotty Front by [/IMG]
Shotty Side by [/IMG]
Shotty Side II by [/IMG]
Shotty by [/IMG]
Mossberg Maverick 88 with ATI Ghost Ring Heat Shield, Millett Optic mount, Surefire Flashlight, Red Dot
Shotty Side by [/IMG]Shotty Side II by [/IMG]Shotty by [/IMG]
- Location
- Minot North Dakota & Las Vegas NV
Nope.... not in oil either.
Casinos!
My 90's throwback piece. Elsewhere on CGN, but thought that I'd bring her here. Brought life back to an old wood Police set, and then had the good luck - and great help - to finally get the forend. Love the classics!
