(forgive me if this is not appropriate to post in this forum but it seemed like the right place.)
Does anyone have an opinion on what this rifle might be worth? Im not really sure what to list it at on the EE and would appreciate some input, i invested a fair bit in this and dealt directly with SEI and crocs on it.
http://imgur.com/a/LaEzQ(PICS HERE)
Started with:
1984 manufacture M1A receiver with very low round count. One of the nicest springfield receivers ive seen or had my hands on.
USGI TRW bolt
USGI Winchester trigger group
USGI Mercury Machine and Tool Oprod
New sage Chassis in black
All sent down to SEI via Crocs guns.
Who did the install/assembly of:
SEI CH 22" medium heavy barrel with M80HT + Fitting of barrel and Headspacing
M80HT of the supplied USGI op rod and M80HT of the sage op rod guide/block+SEI shims for install of sage (not using the rubbish sage shims)
SEI warfighter gas system (SEI cylinder, piston, gas plug)
SEI GLFS
Sadlak NM oprod spring guide
SEI provided chrome silicon op rod spring
SEI extended bolt lock
SEI 4.5 lb MAX-PAK Trigger Upgrade (amazingly good)
SEI connector lock pin and roll pin kit
SEI provided and installed USGI bolt internals
SEI vortex DC flash hider
SEI M14 Scope Mount, Wire EDM
Sadlak mag release
SEI NM front sight, USGI NM rear sight
Some machining was done there as well as a handful of other small items not mentioned. They greased and test fired the rifle and sent it back via an exporter.
Also on the rifle but could be parted out,
GG&G heavy duty bipod
Vortex optics razor HD 5-20x50
Vortex 35mm low rings
Ive had the rifle for 3 years and have put 246 rounds of nosler 175grain and 190 rounds of hornady 168grain tap fpd through it with not a single issue.
I am selling it because my life has changed a fair bit since i got the rifle in 2013 and just i dont use it anymore, as you can see from the round count.
Input welcome.
Does anyone have an opinion on what this rifle might be worth? Im not really sure what to list it at on the EE and would appreciate some input, i invested a fair bit in this and dealt directly with SEI and crocs on it.
http://imgur.com/a/LaEzQ(PICS HERE)
Started with:
1984 manufacture M1A receiver with very low round count. One of the nicest springfield receivers ive seen or had my hands on.
USGI TRW bolt
USGI Winchester trigger group
USGI Mercury Machine and Tool Oprod
New sage Chassis in black
All sent down to SEI via Crocs guns.
Who did the install/assembly of:
SEI CH 22" medium heavy barrel with M80HT + Fitting of barrel and Headspacing
M80HT of the supplied USGI op rod and M80HT of the sage op rod guide/block+SEI shims for install of sage (not using the rubbish sage shims)
SEI warfighter gas system (SEI cylinder, piston, gas plug)
SEI GLFS
Sadlak NM oprod spring guide
SEI provided chrome silicon op rod spring
SEI extended bolt lock
SEI 4.5 lb MAX-PAK Trigger Upgrade (amazingly good)
SEI connector lock pin and roll pin kit
SEI provided and installed USGI bolt internals
SEI vortex DC flash hider
SEI M14 Scope Mount, Wire EDM
Sadlak mag release
SEI NM front sight, USGI NM rear sight
Some machining was done there as well as a handful of other small items not mentioned. They greased and test fired the rifle and sent it back via an exporter.
Also on the rifle but could be parted out,
GG&G heavy duty bipod
Vortex optics razor HD 5-20x50
Vortex 35mm low rings
Ive had the rifle for 3 years and have put 246 rounds of nosler 175grain and 190 rounds of hornady 168grain tap fpd through it with not a single issue.
I am selling it because my life has changed a fair bit since i got the rifle in 2013 and just i dont use it anymore, as you can see from the round count.
Input welcome.
