BCL 102 stripped receiver set thread

DILLIGAF said:
So mine should ship first since i was the first one to buy a set at super full price... lol... ?

tenor.gif
Click to expand...

I’ve been soaking yours in a bucket of maple syrup and sand all weekend. Tomorrow we bake it in the oven at 375% for 9 hours then off it goes :)

Seriously though, black and unpainted sets go out Tuesday/Wed. They get picked up tomorrow...it just depends when UPS gets here.

Ryan
 
DILLIGAF said:
So mine should ship first since i was the first one to buy a set at super full price... lol... ?

tenor.gif
Click to expand...

bananarama said:
take it easy bro, don't jizz on your phone
Click to expand...

Chemist said:
I’ve been soaking yours in a bucket of maple syrup and sand all weekend. Tomorrow we bake it in the oven at 375% for 9 hours then off it goes :)

Seriously though, black and unpainted sets go out Tuesday/Wed. They get picked up tomorrow...it just depends when UPS gets here.

Ryan
Click to expand...

Lol. This is some entertaining ####.:wave::popCorn:

I cant wait for mine.

Ryan, I hate to become another harpy, but I would really appreciate a spec sheet to better understand what parts will fit. While I am super enthusiastic about starting this build, I am nervous as hell about buying parts that wont fit and selling them at a loss...
 
Lower wise, the front pivot pin, the one side of the ambi safety safety and the plunger are proprietary to the 102. All other parts from most AR lower parts kits should work.



onetwentyish said:
Lol. This is some entertaining ####.:wave::popCorn:

I cant wait for mine.

Ryan, I hate to become another harpy, but I would really appreciate a spec sheet to better understand what parts will fit. While I am super enthusiastic about starting this build, I am nervous as hell about buying parts that wont fit and selling them at a loss...
Click to expand...
 
Last edited:
You gotta help a guy out, please Ryan.

Which is the liver pin? And can we source proprietary, and for that matter, any other stock parts we may want through you? Or BCL direct?
 
Well its confirmed, The JP 308 Retaining pin doesn't fit the factory BCL BCG...lol... so you are stuck with a AR15 retaining pin thats to short unless you make the hole a tiny bit bigger :)

I also got my DMPS Pins, Just waiting on my reamer.

31280446_10156416423638552_7579133800030928896_n.jpg
 
Last edited:
Chemist said:
Lower wise, the front pivot pin, the one side of the ambi safety safety and the plunger are proprietary to the 102. All other parts from most AR lower parts kits should work.
Click to expand...

Are the safeties standard or proprietary then? Think I will go for a BAD-CASS set.

No issues with buffer tubes or reciever end plates? Thought I read that the PWS ratcheting one didn't work? That one would be my go to if compatible.

As far as the upper goes, what are we limited to for drop in parts and what works with some fitting/modification? I am about to start shopping around for a BCG, handguard and charging handle so that they get here about the same time as my recievers.
 
Chemist said:
I’ve been soaking yours in a bucket of maple syrup and sand all weekend. Tomorrow we bake it in the oven at 375% for 9 hours then off it goes :)

Seriously though, black and unpainted sets go out Tuesday/Wed. They get picked up tomorrow...it just depends when UPS gets here.

Ryan
Click to expand...



All excited i called today and was told ships in May.

The guy on the phone also said he never heard that it's shipping this week.

I ordered unpainted.
 
All of the black and unpainted sets except for a few of each went out today. I hope to have all of the stripped upper/lowers sets...all colours and unpainted as well as the uppers out mid next week. The remainder should be arriving here tomorrow and heading to be painted on Friday.

Ryan
 
Last edited:
You must log in or register to reply here.
Back
Top Bottom