BCL 102 stripped receiver set thread

Dr. Hunter said:
I found the 308 ar lower parts kit rear takedown pin doesn't fit which was not a big deal since I have a lower parts kit for my slr and don't need the take down pins for it but figure people should know when they buy lpks.

I'm curious as to what the hole under the rear takedown pin is for? My build is pretty much complete just waiting for the bolt catch set screw. Anyone know where one might be able to find one locally in Edmonton?

I'll post some pics and a list of parts tomorrow
Click to expand...
The rear takedown pin is standard AR-15. As with all of the lower parts. Granted you need a trigger that is AR-10 spec and has a strong enough spring to set off harder .308/7.62nato primers.
 
aO9duoW.jpg


EBCGH2w.jpg


Very Happy with this purchase. Wish I bought 2.

I went with Uncoated, will be hard anodizing mine.
 
Anyone know where to find a gen2 handguard and barrel nut in ODG? Building more of a bench rifle, and don't mind the weight, just want a nice flush fit.
 
Quick newb question regarding my new 102:

"- Raptor charge handle ( fitting required unless you have a Gen 1)"
Is the LT version the gen 1 or the gen 2 ?

The website also says these work with AR15 and AR10 platforms. But don't the AR10 CH need to be longer ?

Also, any suggestions for buttstock replacement? I didn't realize the ones the 102 comes with are basically unusable..

Edit: Will the PRS fit on the buffer tube or do i need to replace that too ?
 
Last edited:
Anyone know where to find a gen2 handguard and barrel nut in ODG? Building more of a bench rifle, and don't mind the weight, just want a nice flush fit.
+1

I'll be looking for the same thing
Click to expand...

I'll sell you my black one if I ever get it...
 
Time to put her together. I was also missing the 2 small screws, Had to take them from my NEA15...lol... Ill text you later Ryan :)

So Now that I had time to compare Gen 1 to Gen 2,I like the Gen 1 way better. My workbench is a mess trying to cannibalize parts from my 2 other rifles...

31870224_10156435639868552_6279014720989036544_o.jpg

31768666_10156435666193552_6523952440977391616_o.jpg
 
Last edited:
I have an odg handguard from my original bcl 102 that I can part with if I can find it. The barrel nut is scratched up since it was a ##### to take off but you can't see the marks under the handguard.
 
So there appears to be two different set screws the one originally posted keeps the ambi paddle in place but the hole for the left side of the receiver where originally a roll pin would go is a different sized set screw. It's shorter and narrower than the one originally posted.

Ryan can we have the specs for this other screw
 
DILLIGAF said:
Here is the list of parts that are confirmed to work so far

- JP BCG ( some rifles need different length gas tubes )
- Brownells BCG ( depends on what day your BCL was built )
- Criterion 18.5" .308 AR, Light Weight, 1x10, Chrome Lined Barrel.
- Midwest Industries MI Armalite AR10 One Piece Free Float Handguard #MI-AR10SSM12
- Geissele SSA trigger
- SLR Helix Handguard (Choose DMPS high Armalite nut when checking out)
- BCM/VLTOR Charge Handle ( fitting required unless you have a Gen 1 )
- Phase 5 bolt catch extended v2
- law tactical folder
- Raptor charge handle ( fitting required unless you have a Gen 1)
- Ergo grip
- Triggertech triggers
- JP Silent Capture 308 buffer
- TALON AMBIDEXTROUS SAFETY
- Fulton Armory High pressure bolt ( fits Gen 1 )
- SLR Adjustable gas block
- Fulton Armalite gas tube
Click to expand...

Also the following
Timney AR-10 trigger 670s
X-Caliber barrels
Odin Works hand guard with Armalite barrel nut option
SLR gas tube, mid lenght
JP Enterprises Bolt Buttstock
Magpul Ctr
hogue Grip
 
You must log in or register to reply here.
Back
Top Bottom