Cheap bustard !!!!!i

Reminds me of one of our club rifles I had to "Un-Bubba". I called her Bubba Butt.

Looked like it was trimmed with a dull butter knife.
Bubba_Butt_K31_B.jpg
[/IMG]

The line a couple inches from the butt is the cut line from the knife Bubba used to cut the duct tape covering the pad.
Bubba_Butt_K31.jpg

Bubba_butt_parts.jpg
Bubba_butt_parts_II.jpg


And after finding an original buttplate from Europe.
Bubbareincar.jpg
 
Yes, and because I am a proud mercan , I can't be on the EE,?? otherwise I would post up that Remington slipon, and sell it up nord. What is the a xchang,rate anyway???
 
diopter said:
Reminds me of one of our club rifles I had to "Un-Bubba". I called her Bubba Butt.

Looked like it was trimmed with a dull butter knife.
Bubba_Butt_K31_B.jpg
[/IMG]

The line a couple inches from the butt is the cut line from the knife Bubba used to cut the duct tape covering the pad.
Bubba_Butt_K31.jpg

Bubba_butt_parts.jpg
Bubba_butt_parts_II.jpg


And after finding an original buttplate from Europe.
Bubbareincar.jpg
Click to expand...

I think my work looks better than that. I'll have to work on learning to post pics, old dog, New trix?? Might take a while, but I'll frigger,it out.
 
dugin said:
Yes, and because I am a proud mercan , I can't be on the EE,?? otherwise I would post up that Remington slipon, and sell it up nord. What is the a xchang,rate anyway???
Click to expand...

Your economics may or may not not work here in Canada. The exchange rate is not a good guide. The pair of flip flops would probably be at least 3 bucks in Dolarama and for some reason from a more turdier Chinese factory. The official Remington slip on if available at all would likely retail at least 3-4 times what you paid, no joke. Forget selling footwear just sell the genuine product for a 100 percent mark up and you should do fine ( sad for us)
 
Suther said:
I use a slip on recoil pad on my sks. Not because of the recoil, but due to the really short length of pull. I also use it on my enfield for the same reason.
Click to expand...

Me too. I will put one on the moisin for that reason, and it's wicked recoil. I tried mine out a couple weeks ago; I took 10 rounds of Chinese surplus with me just to see where and how it shot. I fired 5, and that was enough. Rifle shoots great; puts them in less than an inch and a half at 100 yards leaning against a post; my shoulder still hurts depending on how I move it.
 
Ebay sells a $6.00 pad for the SKS. Not only does this tame the brutal recoil from the huge 7.62x39, but it makes the butt 2" longer, whichs it a better fit for me.

I find the full sized Nossy Maggot ok on recoil, but the M-44 makes a #5 feel like a Red Ryder BB gun. It needs a pair of flip flops.

I have done flip flops before. I usually take the steel plate off and glue the show to the wood with contacts cement.
 
apu said:
Your economics may or may not not work here in Canada. The exchange rate is not a good guide. The pair of flip flops would probably be at least 3 bucks in Dolarama and for some reason from a more turdier Chinese factory. The official Remington slip on if available at all would likely retail at least 3-4 times what you paid, no joke. Forget selling footwear just sell the genuine product for a 100 percent mark up and you should do fine ( sad for us)
Click to expand...

Actually, you can get flip flops at Dollar Tree for $1.25. Hell the cheap ones at Walmart are only $3. And my slip on pad (i think it's Allen brand?) came from Walmart for $10.
 
Flip flops, flip flops, flip flops,? Can't you kanucs, get it through your head, it's THONGS!!!!! Easier to spell, it's shorter, and the word just gives me a nice warm fuzzy feeling!!! So there!!!
 
Trim your gun stock with a chainsaw to shorten it to bubba-length
And use bubble wrap for a recoil pad and a rubber band to hold it on!
Cost is 3 cents...
 
You must log in or register to reply here.
Back
Top Bottom