4 options to complete your Stag 10 NR rifle., 308 and 6.5 Creed avail 497.24USD & up

[IRUNGUNS]

Yes it does, we are currently looking into handguards that are compatible. Right now the best option is Midwest Ind. 15" with a .210 upper tang UPC 816537017523. There is also an 18.0" we will be looking into on Monday. If they are readily available we will also offer those.

The pictute shows the receiver set with a pistol grip. Doesnt it come with one?
Would you have a link to the compatible handguards?

thanks!!

 

[Jest4phun]

If we already have an order on the stag 10s upper/lower from before and get this kit was their going to be 1 shipping rate for both or are we buying shipping for each at $50 total?

 

[IRUNGUNS]

If you ordered your receiver set during the Canada Day sale there will be a 25.00USD gift card in your order to rebate the shipping for the build kit.

If we already have an order on the stag 10s upper/lower from before and get this kit was their going to be 1 shipping rate for both or are we buying shipping for each at $50 total?

 

[Jest4phun]

If you ordered your receiver set during the Canada Day sale there will be a 25.00USD gift card in your order to rebate the shipping for the build kit.

........uuuh hate to ask as I guess I missed that memo I did purchase mine during the Canada day sale where would I find my gift card? Cuz in my order I don’t have it and I did order it on July 2nd before the sale went off, I’m sure on another thread you even extended the sale till July third so I’m sure I made it

 

[beltfed]

You had me until I read the bit about .750 gas blocks. If you want a HB SS barrel, why slim it down the rest of the way to a thin profile? These deserve to be served by .936 blocks, and I'd wager a bet they'd shoot better too.

 

[Brian46]

Probably so people can finish turning it down and cut it to 18.5" so we can get an 8lb or less rifle

 

[patjohnw]

Wish I had the money on hand and the time because this post is making me a little hard.. Bah

It's firearm Barbie

 

[IAFS]

Did we get confirmation on the creedmoor twist? 1in8 is the usual suspect.

 

[Adam134]

You had me until I read the bit about .750 gas blocks. If you want a HB SS barrel, why slim it down the rest of the way to a thin profile? These deserve to be served by .936 blocks, and I'd wager a bet they'd shoot better too.

+1.

 

[Brianma65]

Probably so people can finish turning it down and cut it to 18.5" so we can get an 8lb or less rifle

My Stag 10 is a littl over 8 lbs and I have a 20 inch barrel.
I didn’t need to turn it down or cut it off

 

[Brian46]

My Stag 10 is a littl over 8 lbs and I have a 20 inch barrel.
I didn’t need to turn it down or cut it off

20 is just too long imo, all my hunting rifles in 308 would have 16" barrels if I had it my way, but we have to play the legality game

 

[Brianma65]

20 is just too long imo, all my hunting rifles in 308 would have 16" barrels if I had it my way, but we have to play the legality game

Well if 1.4 inches is to much, just chop it off with a hacksaw and recrown it.

 

[Brian46]

Well if 1.4 inches is to much, just chop it off with a hacksaw and recrown it.

When it is already in the lathe to get turned down it will get chopped

 

[ViktorF]

Some Diamond Head Forends on your webpage would probably sell...the same ones Stag Puts on their Rifles.

 

[luc2121]

I second the diamondhead forearms idea

 

[jiffx2781]

Some Diamond Head Forends on your webpage would probably sell...the same ones Stag Puts on their Rifles.

The one you posted is for the low receiver height. This takes the high profile. But ya, the diamondhead handguard is nice

 

[kilo3niner]

Would the Odin 02 lite 17.5 fore end work?

 

[Badger4570]

Any chance we'd see a 7mm-08 setup?

 

[tstormt]

My Stag 10 is a littl over 8 lbs and I have a 20 inch barrel.
I didn’t need to turn it down or cut it off

Did you end up using the faxon pencil barrel ?

 

[Brianma65]

Did you end up using the faxon pencil barrel ?

i just for pics, s I don’t have a buffer and spring