NEW: AutoTrickler V3 Powder Dispensing System (full details)

GreenBob

GreenBob

CGN Ultra frequent flyer
Super GunNutz
Rating - 100%
202   0   0
Location
CGN
"It's here!

AutoTrickler V3. This new version brings Bluetooth connectivity (with free apps), an all-new AutoThrow, and an updated AutoTrickler base. You'll be seeing this system in some hard-core long-range rifle stories here on the channel, so make sure you're subscribed!"


Prices: https://www.autotrickler.com/v3-upgrade-for-ad.html
Full Story: https://bit.ly/2Qk4K39

IMOH: Quality of craftsmanship looks ok, but it doesn't look as good as area 419 reloading. Upgrade price is %#@# and a kick in the balls, as this is/was not a cheap system to purchase in the first place.

V2 to V3 Complete Upgrade Kit for A&D: $290.00U.S
V2 to V3 Upgrade AutoThrow: $220.00U.S
V2 to V3 Upgrade Electronics for A&D: $60.00U.S
V2 to V3 Upgrade Adjustable Base: $20.00U.S (looks cheap)
V3 Accessory Kit: $20.00U.S (looks cheap & overpriced)
 
Last edited:
Well I don’t think anyone gets into this game to save money.
After you have one of these setups you would never be without one.
I will likely upgrade mine this winter.
Adam has pretty much addressed everything with the upgrades
 
Bluetooth is a welcome feature for sure. My dispenser has been 100% once the tension was set. Check it now and again. The trickler base needs to be aluminum as well.
 
I can see myself upgrading to Bluetooth version.
If you want to pimpit up... Area 419.

View attachment 276586

and

Screen Shot 2019-05-25 at 9.41.44 AM.jpg
 

Attachments

  • Screen Shot 2019-05-25 at 9.41.44 AM.jpg
    Screen Shot 2019-05-25 at 9.41.44 AM.jpg
    68.7 KB · Views: 765
Last edited:
I seriously cannot justify spending money on 3D printed parts. It looks like an awesome system overall, but unless those parts are either injection molded or cast, I can't spend the money on them.
 
Blastattack said:
I seriously cannot justify spending money on 3D printed parts. It looks like an awesome system overall, but unless those parts are either injection molded or cast, I can't spend the money on them.
Click to expand...

Are 3D printed parts inferior in his application? I don't know much about 3D printing.
 
My V2 setup has thrown at least 1500 loads by now,
No sign of usage whatsoever in the plastic.

Only sign of use by now, is rubber o-ring (that's used as a belt) behind the trickler, between motor and trickling tube, is starting to crack up.
I suspect it's going to fail soon.
 
Way too complicated to do a single task.

The auto measuring systems we have now are much simpler and more economical.

And no, this isn't easier and simpler, it's somebody trying to reinvent something to reveal their big discovery.

I'll stick with the charge master.
 
Chargemaster is nowhere near as accurate as an FX120,
Had both, tested out both side by side.

Being simpler to use was it's only feature,
But it throwed either +/- 0.08gn off either ways, which you make 0.16gn differences between extreme lows and highs, all while always displaying 42.7gn on the scale.
These same loads measured between 42.62gn and 42.78gn on the FX120.
On top of that chargemaster is slower to trickle.

I'll take more complicated but faster/more accurate any time!
 
Kelly Timoffee said:
Way too complicated to do a single task.

The auto measuring systems we have now are much simpler and more economical.

And no, this isn't easier and simpler, it's somebody trying to reinvent something to reveal their big discovery.

I'll stick with the charge master.
Click to expand...

Nothing wrong with CM1500, especially when you combo it with GemPro250.
That said, you are comparing apples and oranges.
 
Has anymore ordered the FX120i recently?

Quite confusing with the various Cambridge Environmental websites.. based in Canada, charging in USD, etc etc.

Best deal I can see now is the scale at $475USD without any of the specialized reloading add-ons. Then just order the V3 upgrades directly from Auto Trickler (.com). Again, based in Canada, but charge in USD.

Then perhaps get some Area 419 bling.

As some have mentioned, it's a lot of coin, but I've reached a point in my life where I can splurge and buy some luxury items to play around with. It's a hobby, and not one i'm doing to save money.
 
Hi Steyr101,

Give this guy a call, he can help you and/or answer any of your questions.

Trevor ###XX
1-800-535-3751
w**.cambridgeenviro.com
 
I got some V2 to V3 upgrades on order. I'm looking forward to the Bluetooth functionality, especially to dial in powder charges. I never saw the need for the auto throw. I use Lee dippers and by the time I seat and crimp the bullet the next powder charge is usually just about done.
 
You must log in or register to reply here.
Back
Top Bottom