Turknelli M4 is HERE AT LAST!!!! TAC 12 BY Trigger wholesale!!!!
- Thread starter badboybeeson
- Start date
- Location
- East ontario
correct
just installed the fixed stock, some tips for anyone who wants to install one on their turknelli
first off, the turks made it way harder than it needed to be, way harder than the benelli, i don't know why they didn't just copy the stock like they did everything else, but moving on...
once you verify the gun is unloaded, clear and safe
dissemble it, it makes life a whole lot easier, remove the trigger group specifically
**Can-Down informed me if you pull the adjustment lever down by hand further than it cams when you depress the lever you can slide it off the tube that way, i had tried pulling it the other way like an ar-15 stock and it didn't work and i legit never thought of using his method so try his way first and if it doesn't work for whatever reason try the method i used like a dingus below
on your telescoping stock, look at the lever you squeeze to adjust the stock, see that tiny rollpin that holds the plunger spring in? drift that out, the spring underneath is under a little bit of tension so wear safety glasses and don't let that spring fly across the room
once the spring comes out squeeze the lever and pull the stock back and off the gun
next is the pistol grip, rotate the grip and screw it off. it will remain trapped on the recoil buffer tube but with it slid back out of the way you will see a silver hex nut. you will need a 27mm wrench to loosen it, BEFORE YOU DO I RECOMMEND PUTTING A WITNESS MARK ON THE THREADS, THE NUT, AND THE RECEIVER TO KNOW HOW DEEP EVERYTHING WAS THREADED IN FOR REASSEMBLY, I USED A SHARPIE PAINT MARKER
once loose you can then un thread the entire recoil buffer tube off of the receiver. once off, thread the hex nut the opposite direction you did before and remove it straight off the tube. then slide your pistol grip back to the threads and begin threading it back on as if you were tightening it, keep going and going, it will take a bit but eventually it will thread right off the tube
replace the hex nut on the tube and thread the tube back into the receiver, tighten everything back down to where it was before you disassembled it, hopefully you put witness marks on there. make sure the track with the retaining detent for the telescoping function is clocked correctly (if your front and rear sight are parallel with the sky your detent portion of the tube should be facing the floor. i know this is obvious to 99% of you but remember car manuals have warnings that cruise control is not auto pilot for a reason
now slide your fixed stock onto the gun. if you haven't removed the buttplate yet you unscrew the sling swivel and the buttplate pivots off from bottom to top. you may have your spacer, washer, bolt and hex key inside it.
once the fixed stock is seated place the black plastic spacer inside the stock. there will be a side that says "top" on it, that is the side you want facing out towards you. again with your sights parallel to the sky you want the word "top" at the 6 oclock position
now put your bolt through the washer, then put it through the slot in the black plastic spacer, make sure your screw is seated properly in the threads and tighten. with mine there was absolutely no room for the bolt to engage the threads with the washer. i tried it without the washer but i didn't feel comfortable not having the washer there to distribute the force so i removed the spacer and touched the area of the spacer the washer contacts to the belt sander, a little bit at a time. you might not have to do this but these stocks, although decent outside, are crude inside and may require fitting
once everything is threaded together replace the buttplate, remember it hooks in at the top then pivots in at the bottom, then screw in the sling swivel to secure it and you are done. now reassemble the gun, the trigger guard may take a bit of fiddling, i found it didn't go back in as smoothly as it did with the pistol grip but it did go in without modification or anything
the length of pull on the fixed stock is identical to the telescoping stock on its most extended position
the area where the trigger group sits into the stock may be a little rough, a few light passes with an emery board or sand paper will clean it up
the stock feels nice, its fairly attractive, im not crazy about the little squares for the grip section but they feel pretty good and i think it would make a great candidate for stippling. im not sure if i like it more or less than the telescoping stock but we'll see how it feels under recoil
i hope this helps someone out
first off, the turks made it way harder than it needed to be, way harder than the benelli, i don't know why they didn't just copy the stock like they did everything else, but moving on...
once you verify the gun is unloaded, clear and safe
dissemble it, it makes life a whole lot easier, remove the trigger group specifically
**Can-Down informed me if you pull the adjustment lever down by hand further than it cams when you depress the lever you can slide it off the tube that way, i had tried pulling it the other way like an ar-15 stock and it didn't work and i legit never thought of using his method so try his way first and if it doesn't work for whatever reason try the method i used like a dingus below
on your telescoping stock, look at the lever you squeeze to adjust the stock, see that tiny rollpin that holds the plunger spring in? drift that out, the spring underneath is under a little bit of tension so wear safety glasses and don't let that spring fly across the room
once the spring comes out squeeze the lever and pull the stock back and off the gun
next is the pistol grip, rotate the grip and screw it off. it will remain trapped on the recoil buffer tube but with it slid back out of the way you will see a silver hex nut. you will need a 27mm wrench to loosen it, BEFORE YOU DO I RECOMMEND PUTTING A WITNESS MARK ON THE THREADS, THE NUT, AND THE RECEIVER TO KNOW HOW DEEP EVERYTHING WAS THREADED IN FOR REASSEMBLY, I USED A SHARPIE PAINT MARKER
once loose you can then un thread the entire recoil buffer tube off of the receiver. once off, thread the hex nut the opposite direction you did before and remove it straight off the tube. then slide your pistol grip back to the threads and begin threading it back on as if you were tightening it, keep going and going, it will take a bit but eventually it will thread right off the tube
replace the hex nut on the tube and thread the tube back into the receiver, tighten everything back down to where it was before you disassembled it, hopefully you put witness marks on there. make sure the track with the retaining detent for the telescoping function is clocked correctly (if your front and rear sight are parallel with the sky your detent portion of the tube should be facing the floor. i know this is obvious to 99% of you but remember car manuals have warnings that cruise control is not auto pilot for a reason
now slide your fixed stock onto the gun. if you haven't removed the buttplate yet you unscrew the sling swivel and the buttplate pivots off from bottom to top. you may have your spacer, washer, bolt and hex key inside it.
once the fixed stock is seated place the black plastic spacer inside the stock. there will be a side that says "top" on it, that is the side you want facing out towards you. again with your sights parallel to the sky you want the word "top" at the 6 oclock position
now put your bolt through the washer, then put it through the slot in the black plastic spacer, make sure your screw is seated properly in the threads and tighten. with mine there was absolutely no room for the bolt to engage the threads with the washer. i tried it without the washer but i didn't feel comfortable not having the washer there to distribute the force so i removed the spacer and touched the area of the spacer the washer contacts to the belt sander, a little bit at a time. you might not have to do this but these stocks, although decent outside, are crude inside and may require fitting
once everything is threaded together replace the buttplate, remember it hooks in at the top then pivots in at the bottom, then screw in the sling swivel to secure it and you are done. now reassemble the gun, the trigger guard may take a bit of fiddling, i found it didn't go back in as smoothly as it did with the pistol grip but it did go in without modification or anything
the length of pull on the fixed stock is identical to the telescoping stock on its most extended position
the area where the trigger group sits into the stock may be a little rough, a few light passes with an emery board or sand paper will clean it up
the stock feels nice, its fairly attractive, im not crazy about the little squares for the grip section but they feel pretty good and i think it would make a great candidate for stippling. im not sure if i like it more or less than the telescoping stock but we'll see how it feels under recoil
i hope this helps someone out
Last edited:
i had tried on mine to pull the lever end down just like you would with an AR stock but it did not want to budge and i was afraid it would break but i hadn't tried pulling the plunger end of the lever down in its normal direction of travel by hand. i will update the write up in case other peoples stocks are a little smoother like yours
Last edited:
- Location
- East ontario
- Location
- East ontario
Already asked you on Instagram but you have this exact one for sale or another finished like this I can purchase now Simon??
- Location
- East ontario
DAMN, thanks Simon!!
- Location
- East ontario
no we have not got an answer.
feel free to contact them if you have an issue or a question, we have only 3 people on staff at the retail shop and its all we can do to keep on top of things right now.
i,m in the shop now since 7am building guns and filling orders.
here you go
https://www.triggerwholesale.com/Contact.htm
wolf300H&H
CGN Regular
- Location
- Cabin in central Alberta
Alrighty so finally got out shooting it at farm. 1 st shot magpie down , with my boy so that was cool. Sighted in for slugs like 20 ish yards
Anyhow gun won't rack back empty or cycle , need help here Simon. I checked the O rings on those two rods , there fine. I tightened up more and also break cleaned out the receiver thinking it might not like so much Lube. No luck. Tried a 3" shell to see if it would lock back. Nope.
Putting back together I noticed the rotating bolt has like zero tension .... is that supposed to be like that ? And doing that if the bolt locks back a certain way to re install I'm not sure if I did that right ?
Also the roll pin for bolt release fell out 2nd / mercy shot on magpie how I managed to be watching that idk. I mushroomed it etc etc
Anyhow how we fix this ? Send back ? Bigger o ring on those things ? Not much fun having a semi semi. Thanks. Anyone else chime in too please if got any ideas
Anyhow gun won't rack back empty or cycle , need help here Simon. I checked the O rings on those two rods , there fine. I tightened up more and also break cleaned out the receiver thinking it might not like so much Lube. No luck. Tried a 3" shell to see if it would lock back. Nope.
Putting back together I noticed the rotating bolt has like zero tension .... is that supposed to be like that ? And doing that if the bolt locks back a certain way to re install I'm not sure if I did that right ?
Also the roll pin for bolt release fell out 2nd / mercy shot on magpie how I managed to be watching that idk. I mushroomed it etc etc
Anyhow how we fix this ? Send back ? Bigger o ring on those things ? Not much fun having a semi semi. Thanks. Anyone else chime in too please if got any ideas
