Spectre Ballistics Light Practical Carbine - NR Receiver Set

[Camp Cook]

Little more to barrel length than that if the barrel was manufactured shorter than 18" it can be installed if its longer than 18" it cannot be shortened to less than 18" though.

 

[AbHobbyist]

Little more to barrel length than that if the barrel was manufactured shorter than 18" it can be installed if its longer than 18" it cannot be shortened to less than 18" though.

CC

You make a good point!!

However to be Fair, and to clarify, I was speaking about barrel that were "manufactured" in short lengths, or lengths under 18.5".

Cutting a barrel down is a whole different "kettle of fish" all together!!

regards

AbH

 

[Camp Cook]

Wasn't commenting against your post was just sharing for those that do not understand how our laws are written

 

[Geoff B]

Considering the 26" OAL for non-restricted , how long is the new receiver compared with a typical AR receiver?
Some of these short barrels may not make the cut-off.

 

[Camp Cook]

My single shot 14" barreled T/C Contender carbines are 27.5" OAL with a 13" length of pull so with a lets say 4" receiver added I'm sure you can run 10" or shorter barrels that is unless you have collapsible or folding stocks...

 

[Geoff B]

I don't think the flash-hider counts toward barrel length, just the chamber and rifled part of the barrel.

 

[MJS]

I don't think the flash-hider counts toward barrel length, just the chamber and rifled part of the barrel.

Not in Canada no,in the US a permanently pinned(welded) brake would count

 

[frabill]

I don't think the flash-hider counts toward barrel length, just the chamber and rifled part of the barrel.

If the flash hider is machined into/from the barrel it counts. Herron arms has done this.

 

[SpectreBallistics]

If the flash hider is machined into/from the barrel it counts. Herron arms has done this.

This is correct.

Muzzle devices do count towards overall length however.

 

[Geoff B]

My AR with a 10.5" barrel measures 27" with the stock fully closed and a short flash hider. Is the SBI receiver set the same length as an AR receiver? If so, I can build a NR carbine! Or buy a longer flash hider.

 

[Dexter Morgan]

I don't think the flash-hider counts toward barrel length, just the chamber and rifled part of the barrel.

True. But irrelevant for a manual action gun.

The overall length of the gun needs to be 26" overall. That's it.

 

[Geoff B]

True. But irrelevant for a manual action gun.

The overall length of the gun needs to be 26" overall. That's it.

That's why I asked the length of the new receiver. The AR is 27" now, so if the SBI receiver is the same length, I can just swap parts and have a NR gun.

 

[S-357]

Will we be able to get them in raw aluminum? I think that would be kind of cool

 

[captainamazing]

Will we be able to get them in raw aluminum? I think that would be kind of cool

Looks cool but not near as tough as anodized. It will dent easily.

 

[SpectreBallistics]

Will we be able to get them in raw aluminum? I think that would be kind of cool

No. Anodizing is a critical step and needed to ensure a durable product.

 

[glockguy-187]

When are you guys hoping for an frt?

 

[jiffx2781]

Why are you guys hoping for an frt?

FIFY







Ready to buy one if you change your mind SB

 

[SpectreBallistics]

When are you guys hoping for an frt?

As quickly as possible.

 

[AOWM]

I’ll be getting this regardless of ban or not.

 

[MartinRiggs]

I’ll be getting this regardless of ban or not.

Same! This will be a great addition regardless of rule changes. Thanks for your hard work guys!