MRA Renegade Rifles, Parts, and Kits now available

Maple Ridge Armourer said:
Tighten to the point the charging handle does not wiggle and no more. This should result in a firm fitment without breaking the bolt. If you break a bolt, we will replace it.
Click to expand...

Thanks you were 100% right :) just tightened it a tiny bit more and then backed it off and repeated and got it to tighten up properly. I was just hesitant with my pension for breaking little things but you called it thanks !
 
Dmitri said:
Hmm.. but i thought you said you will have those.. maybe perhaps a small batch of 12.5" grendel barrels... PLEASE PLEASE PLEASE

EqUGPFL.jpg

5PXWRuf.jpg
Click to expand...

You really want a low velocity, inaccurate barrel?

We thought it would work out but testing has shown the Grendel needs a minimum of 16" barrel.

If you are seeking a short barrel for hunting, a 12.5" 300BLK would perform better.
 
Denka said:
let me know when you can address cerakote, I will bring it and you deal with wobles as well then
Click to expand...

Sure you are welcome anytime! We will absolutely resolve the colour mismatch if in our opinion, the variation is out of acceptable tolerance.


When mass producing parts, there is an acceptable tolerance to strike a fine balance between fit and optimized run time. The wobble you are referring to is likely caused by your particular part being on the high side of the tolerance. When we reviewed part fitment on the high side of the tolerance, we found the wobble to be very minor and well within acceptable limits based on similar high end products in the marketplace. If the minor wobble is unacceptable, you can tighten fitment up with a 1/4-28UNF tension screw. This is not a warranty issue.
 
Do you sell the nylon tipped tension screws, I have 5 AR-15 and none of them have the tension screws ( None of them have wobble ) so I can't take one from there. The only place I have found them is in the USA
 
Apologies if it's already been asked; do you guys plan on producing more 7.62x39 barrels? 12.5" or 14.5" would be ideal.
 
1/4" - 28 set screws are very popular in regular (non-firearm) machinery.

Any industrial supply store will have them.
 
Put in my preorder Sept 20-ish with SFRC. Realize I’m probably late to the party but hoping for a shiny new firearm in the next couple of weeks 🤩

Thank you for giving my AR furniture a fun new place to hang out :)
 
I put together my Renegade rifle kit today.
No problems at all.

There was a bit of wobble. But I used a 1/4-28 set screw to snug it up.
There's zero wobble now.
 
Dexter Morgan said:
I put together my Renegade rifle kit today.
No problems at all.

There was a bit of wobble. But I used a 1/4-28 set screw to snug it up.
There's zero wobble now.
Click to expand...

^^ This ^^
1/4 -28 set screw and any wobble that was present is gone.

Getting lots of looks and questions at the range
Thanks Maple Ridge for a sweet addition to my firearms family

Shoot straight - chrisco
 
Dmitri said:
I got one of the first ones from SFRC, anodizing looks pretty good, or it could be the lighting, have to look at it outside.. :)
Oep58gi.jpg


To guys at MRA: when is the ETA for 12" 6.5 grendel barrels ??? And thanks a lot, im really loving this kit so far..
Click to expand...

This looks excellent! What stock is it? I might have to do something like this for my .308 build once MRA offers those :)
 
^^ This ^^
1/4 -28 set screw and any wobble that was present is gone.
Getting lots of looks and questions at the range
Thanks Maple Ridge for a sweet addition to my firearms family
Shoot straight - chrisco
Click to expand...

To be fair; Not everyone has a 1/4-28 set screw laying around.
Perhaps one should be included in the kit?

I have stuff like this laying around, so it's a non-issue for me.
But others might have to go out looking for one.
 
You must log in or register to reply here.
Back
Top Bottom