MRA Renegade Rifles, Parts, and Kits now available

Ustauk said:
... With the Renegade, you can use an extremely short barrel if the muzzle device and stock add enough length to still exceed the 660 mm OAL.
Click to expand...

Could use an AR-10 buffer tube, an inch longer than the regular AR-15 variety, and buy a bit of length that way if needed.
 
My initial Renegade build is done. I got my hands on a 18.6" 300 Blackout barrel before my receiver showed up. I'm currently waiting on a 12.5" barrel. I'm super happy with the performance so far. Took it out today and got a good 3 shot group after my initial sight in.

The tape on the barrel shows where the 12.5" barrel will end once it's installed. With the 12.5" barrel, no muzzle device and the stock fully collapsed I've got an OAL of 26.25"

CM7GsZO.jpg
 
Here it is so far, Its been trying, Was trying to put my DD MK 18 10.3" barrel on but for the life of me can not get the taper pin out of the gas block, Which is odd because it hasn't been in that long! so after I I couldn't get that off I started ripping apart my 14.5 comp gun(sad day) Put the UBR stock on, had to do a lot of grinding/filing in order to get the end plate to work properly. Put in my trigger tech and my KNS speed safety, One of them doesn't like this frame, If I rack the bolt, pull trigger with safety on nothing happens(but you hear a very faint click) but as soon as I disengage the safety it fires, Not a fan. so may try a different trigger/Safety combo. the brake and the stock aren't fully tightened, I added my silent capture system as well. has to use the provided spacer that came with the UBR stock, Luckily I still had it. Was going to add my 1-8 scope, But I remembered when I tightened down the mount I went a little far and semi stripped two of the screws on the mount, Wasnt worried at the time since I never really planned to take it off, well that came back to bite me tonight as well. Will have to drill out the screws to get it off my Armalite upper. Also noticed the lower was not a fan of the Armalite mag catch It would bind when pressed, Had to swap it for a DD one. Here she is at it stands right now. Still a work in progress.

UFVBbvD.jpg


5W2Du53.jpg
 
Last edited:
Interestingly, I have a Ceiner drop in kit (or two) at home.....I tried sliding one into the upper, and it doesn't fit. The diameter of the bolt carrier is, obvioiusly different.

Of note, I just received my kit last night from a (non board sponsor) dealer out west that had stock last week. I'll be assembling probably tonight.

Pictures to follow.

NS
 
Maple Ridge Armourer said:
We have shipped orders to True North Arms, SFRC The Ammo Source, and Red Deer Shooting Center today.

We are shipping out roughly 30% of the MRA web orders today.

This time next week, I expect to ship more Renegades to dealers to fulfill their pre-orders and 40% of the MRA web orders.

First week of October we plan to ship all the remaining Sept MRA pre orders and most if not all the Aug MRA pre orders.
Click to expand...

Hi there,

I ordered from you July 4th, in time for the Sept pre-order. I have received and built my receiver from SFRC but am still waiting on the receiver, reaction rod anda few other misc parts from you.

I still dont have any shipping info.

I have sent an inquiry through your website and have called a couple of times.

Can you please be so kind as to provide an update on where you are with orders?

Thanks!
 
STEELCITYSLICKER said:
Hi there,

I ordered from you July 4th, in time for the Sept pre-order. I have received and built my receiver from SFRC but am still waiting on the receiver, reaction rod anda few other misc parts from you.

I still dont have any shipping info.

I have sent an inquiry through your website and have called a couple of times.

Can you please be so kind as to provide an update on where you are with orders?

Thanks!
Click to expand...

All pre orders will be completed and shipped this Friday. We will have on hand inventory of more kits by the following week and inventory of complete rifles by Week 4 of October.
 
We have now completed shipping all MRA direct pre-orders minus a few for which we are still awaiting payment.

We have left phone messages and emails to the few remaining customers who need to complete payment. Please complete payment so we can ship your kits.

We will have inventory of receiver kits, complete rifles, complete uppers, and parts by the end of next week.
 
Maybe a dumb question from someone who’s never built a rifle like this but...is it possible to build one of these in 9mm? The way things are going I might not have anything to shoot all my 9mm ammo.
 
KBCL said:
Maybe a dumb question from someone who’s never built a rifle like this but...is it possible to build one of these in 9mm? The way things are going I might not have anything to shoot all my 9mm ammo.
Click to expand...

To our knowledge, there is no way to make this for 9mm. We are working on something else for 9mm.
 
You must log in or register to reply here.
Back
Top Bottom