Where can I buy this Ruger 10/22 Tandemkross left hand charging handle

Thorsbear

Thorsbear

CGN Regular
Rating - 100%
73   0   0
Looking to buy one of these Ruger 10/22 Left side charging handle by Tandemkross Advantage


The quality looks great and functional too.

Everywhere I checked in Canada doesnt have any instock and I need one pretty bad
 
Suther said:
Hadn't seen that product before. Interesting! The rail itself looks weird though? That doesn't look like real picatinny?
Click to expand...

I just ordered from Tandemkross. The latest version looks to have been revised to the more traditional picatinny

www. tandemkross.com/Advantage-Charging-Handle-and-Picatinny-Scope-Base-for-the-Ruger%C2%AE-1022%C2%AE_p_216.html

Thanks everyone for the help! I never would have guessed to try and even order from the US. Shipping right to my house Awesome!!
 
Thorsbear said:
I just ordered from Tandemkross. The latest version looks to have been revised to the more traditional picatinny

www. tandemkross.com/Advantage-Charging-Handle-and-Picatinny-Scope-Base-for-the-Ruger%C2%AE-1022%C2%AE_p_216.html

Thanks everyone for the help! I never would have guessed to try and even order from the US. Shipping right to my house Awesome!!
Click to expand...

That does look better!
 
what they did not show was using the regular chartering handle by ruger once this modification is installed

is it harder to get your fingers in to the regular right hand charging handle?

sure looks like it

they should have sent it to you for free they will get 50 orders based on this thread
 
Jefferson said:
what they did not show was using the regular chartering handle by ruger once this modification is installed

is it harder to get your fingers in to the regular right hand charging handle?

sure looks like it

they should have sent it to you for free they will get 50 orders based on this thread
Click to expand...

It looks like it would get in the way a bit, but not a lot. At rest the part that interfaces with the factory charging handle sits infront of the charging handle far enough that I think it wouldn't cause a big issue unless you have massive sausage fingers. Of course, if you are going to use the factory handle why would you bother putting one of these on?

Look at 1:05 of the video in the OP, it shows the gap between the tandemkross product and the factory charging handle.
 
Suther said:
It looks like it would get in the way a bit, but not a lot. At rest the part that interfaces with the factory charging handle sits infront of the charging handle far enough that I think it wouldn't cause a big issue unless you have massive sausage fingers. Of course, if you are going to use the factory handle why would you bother putting one of these on?

Look at 1:05 of the video in the OP, it shows the gap between the tandemkross product and the factory charging handle.
Click to expand...

On the Tandemcross website the left hand charging handle is shown working with an oversized skeletonized right side charging handle so it shouldn't be an issue
 
BeaverMeat said:
Too bad they don’t make a model with an integral rear sight.
Click to expand...

I believe you would need a raised from sight too, the way the charging handle runs across the top of the receiver and then down to the factory charging handle would likely necessitate both the front and rear sight being higher than normal to be of any use.
 
Suther said:
I believe you would need a raised from sight too, the way the charging handle runs across the top of the receiver and then down to the factory charging handle would likely necessitate both the front and rear sight being higher than normal to be of any use.
Click to expand...

Recess, or grove the charging handle... or perhaps design a top rail like the SEI M14 scope mounts with a hole drilled through it. There are ways.

The design is fairly chunky
 
Last edited:
You must log in or register to reply here.
Back
Top Bottom