Turknelli 2.0 have arrived!!!

What’s the barrel lengh? Don’t see anywhere

Does it come with the factory parts too? Handle, Normal sling without rail etc.

Comes with other chokes still or just breach?
 
Last edited:
scott said:
What’s the barrel lengh? Don’t see anywhere

Does it come with the factory parts too? Handle, Normal sling without rail etc.

Comes with other chokes still or just breach?
Click to expand...

18.5 inches barrel, comes with factory safety and charging handle in adding to the s&j hardware parts.

clone made by aksa arms model s4 but made to s&j specs.

it comes with 3 chokes
 
I got mine on Tueday but didn't have much time to play with it. I put the S&J charging handle in it with no issues. Overall it looks very well made. The Bad Tab is nice. It took me a couple of minutes to figure out the stock but it seems really solid in all positions. I didn't have time to play with the chokes and am curious what the breacher choke is. Cylinder? The shell pouch and holder are very nice too.
 
Chumlee Bumsnag said:
I got mine on Tueday but didn't have much time to play with it. I put the S&J charging handle in it with no issues. Overall it looks very well made. The Bad Tab is nice. It took me a couple of minutes to figure out the stock but it seems really solid in all positions. I didn't have time to play with the chokes and am curious what the breacher choke is. Cylinder? The shell pouch and holder are very nice too.
Click to expand...

The breacher is cly bore
Bbb
 
I just got my Turknelli 2.0 last week and tried to do a full cleaning but couldn't remove the trigger assembly. Is there a trick to removing it?
 
check out a benelli m4 disassembly video, it is the same. I had never taken one apart before and did it the first time without too much trouble, you pretty much have to pull forward and down on it once you've removed the pin and made sure all pieces are removed in order and safety on proper position.
 
Sekler said:
check out a benelli m4 disassembly video, it is the same. I had never taken one apart before and did it the first time without too much trouble, you pretty much have to pull forward and down on it once you've removed the pin and made sure all pieces are removed in order and safety on proper position.
Click to expand...

Yeah, I watched a bunch of video's and tried pulling forward and down. It moves about a 1/16th of an inch forward then stops. With the bolt out I can't see anything holding it back.
 
ryushi said:
Yeah, I watched a bunch of video's and tried pulling forward and down. It moves about a 1/16th of an inch forward then stops. With the bolt out I can't see anything holding it back.
Click to expand...

Did you press on the bolt release button while trying to remove it?
 
Just an update.

I finally got the trigger assembly out. I had to carefully twist a flat screw driver between the trigger guard and the pistol grip.
The tolerances were really tight and I had to use a rubber mallet to get it back in. I did this a few times and now I can remove it without the
use of tools.
 
I went ahead and ordered the 8.5" Mesa Truckee fore grip. Has anyone tried putting one of these on a 2.0? I looked at the 11' one but just need a place to mount a small weapon light. Maybe an Odin mini. I looked at the B&T handguard but it's a bit to 'tactical' for my liking.
I finally got some time to spend familiarizing myself with stripping and reassembling it. Getting the bolt rat tail to go into its place gave me a bit of grief. I used the Bad Tab to push it down while reinserting the bolt.
I found that turning the charging handle while pulling on it will let it pop right out. No rubber hammer!
 
ryushi said:
Just an update.

I finally got the trigger assembly out. I had to carefully twist a flat screw driver between the trigger guard and the pistol grip.
The tolerances were really tight and I had to use a rubber mallet to get it back in. I did this a few times and now I can remove it without the
use of tools.
Click to expand...

Good day.
Sorry must have missed this.
Was you gun one of the OD green guns by chance
We did notice some were,very tight
Bbb
 
badboybeeson said:
Good day.
Sorry must have missed this.
Was you gun one of the OD green guns by chance
We did notice some were,very tight
Bbb
Click to expand...

No, it was a black one. No worries though, I got it apart a few times now and fitted a Mesa Tactical Urbino stock set.
 
ryushi said:
No, it was a black one. No worries though, I got it apart a few times now and fitted a Mesa Tactical Urbino stock set.
Click to expand...

I'd like to see a picture of the Mesa stock but the settings on this forum don't let me post a picture direct from computer or phone. Can you change this Simon? Pics are good!;)
 
Been ages since I've posted on CGN but I am very excited to have discovered S&J's fantastic Turknelli offerings! Benelli M4s have been a dream gun of mine since highschool, back when I was a junior technician and sales guy at Wanstalls (with Tony Wanstall himself). Finally those patents are up, and Canadian shotgun experts are delivering comparable quality "proshopped" imports. What a time to be getting back into shooting!! Thanks BBB, I got your email earlier and really looking forward to getting one of these. Cheers!!
 
I had my 2.0 at the range yesterday for a bit of fun and the rubber pistol grip cover came off. I tried some Gorilla glue in the glue gun but it didn't adhere to the rubber. Any suggestions? Epoxy?
 
shotzee said:
How have the shotguns been with target loads? Looking at maybe using this for skeet/3 gun.
Click to expand...

Mine still needs to be broken in more but I had to manually cycle every round with target load. I was using the Challenger Target load. YMMV. Buck and slugs though, no prob.
 
You must log in or register to reply here.
Back
Top Bottom