SOLD OUT: TR-410 Micro

[Deathrawt]

I don’t mind these 410/45 revolvers but they need to address that weak spot in the main frame up front where the gas gets deflected and they need to make the rear part where the firing pin is out of steel too as the soft turkaluminum wears from the thrust from the shells when fired
Also shorten the revolver cylinder to just take 2.5 inch shells and not 3 inch
This will or should help with accuracy shooting the 45 colt
Those new 357 revolvers with the 3inch length revolver cylinders that don’t shoot any shotgun shells whatsoever are just idiotic

 

[Deng577]

I don’t mind these 410/45 revolvers but they need to address that weak spot in the main frame up front where the gas gets deflected and they need to make the rear part where the firing pin is out of steel too as the soft turkaluminum wears from the thrust from the shells when fired

Really? I have about 600 rounds through my XR-410 and there's no damage to the breech face.

 

[Deathrawt]

The micro I had was starting to show wear there
You could see the ring from the 410 shell head/primer
Only shot 50 rounds through it

 

[Deng577]

The micro I had was starting to show wear there
You could see the ring from the 410 shell head/primer
Only shot 50 rounds through it

Mine has that too. It's just paint/blueing scuff.

 

[Deathrawt]

Eventually I expected there to be wear there but 50 rounds isn’t a lot
I have another 410 with a 14 inch barrel but only shot maybe 10 rounds through it and it has zero wear on it
It’s possible the coating/blueing is just thin and comes off easily and that’s why it was showing wear
It didn’t affect the function of it whatsoever

 

[Deng577]

Eventually I expected there to be wear there but 50 rounds isn’t a lot
I have another 410 with a 14 inch barrel but only shot maybe 10 rounds through it and it has zero wear on it
It’s possible the coating/blueing is just thin and comes off easily and that’s why it was showing wear
It didn’t affect the function of it whatsoever

I'll take some photos of mine when i get off work tonight.

 

[Scruffer]

My backup if i missed the TR-45 was going to be the Canuck Evolve 357 9" revolver. Barrel length is twice that of the Micro but in a better caliber. Does cost more though.

I got it a week ago didn’t think Micros would come. Never shot it yet quality control from factory not to good, mine had a dent on muzzle touching rifling also was never oiled and rifling was rusted. Store I purchased said to contact warranty, sucks for new gun. Other than that cylinder and breach were tight. Everything else looked good, nice to have it in 357/38 factories are just trying to spit these out.

 

[Deng577]

I got it a week ago didn’t think Micros would come. Never shot it yet quality control from factory not to good, mine had a dent on muzzle touching rifling also was never oiled and rifling was rusted. Store I purchased said to contact warranty, sucks for new gun. Other than that cylinder and breach were tight. Everything else looked good, nice to have it in 357/38 factories are just trying to spit these out.

Good grief that's horrible.
I'm going to P&D to look at one in person next week.

 

[Deng577]

Eventually I expected there to be wear there but 50 rounds isn’t a lot
I have another 410 with a 14 inch barrel but only shot maybe 10 rounds through it and it has zero wear on it
It’s possible the coating/blueing is just thin and comes off easily and that’s why it was showing wear
It didn’t affect the function of it whatsoever

Well, this is what 600 rounds looks like. Mostly buck and slug.

 

[Scruffer]

Well, this is what 600 rounds looks like. Mostly buck and slug.

ya that’s normal