- Location
- Edmonton Area Ab, Candle Lake Sk
The SBI Receiver your looking for is a ST-22, tandonize in stock, black out of stock
10/22 build
- Thread starter Baked Potatoe
- Start date
Magdump.ca is their store website. The black ST-22 receiver is out of stock at the moment but they have it in Tanodize colour if you're interested in that.
https://magdump.ca/47-1022-receivers
If you want black give them a call and see when they're going to do another run. They sell out quickly when in stock but they are replenished often.
It looks like if you are in Canada Magdump is the only option.
The receiver with the rear charging handle is listed, the black is currently out of stock but the Tanodize is available:
https://magdump.ca/47-1022-receivers
What brake is on this one?
What barrel?
Sad to see DLASK is basically done for, they had very attractive pricing and legendary reviews...
As always, by the time I show up to the party it is over.
Looks like an old Grey Birch setup. (Receiver and barrel).
Grey Birch RDR. Threaded barrel i to receiver. No V block. Very slick.
Bought just Minutes b4 they pulled up stakes and fled to FLA.
SBI bolt (formerly kidd, formerly formerly GB).
Dlask products can still be found at Advent Arms and last i heard they were sourcing barrels of the Dlask vintage.
Check them out
Thank you again everyone. Im compiling my list.
My question is hand guard. Are there any available that are long enough for a proper C grip. 16 inches and up would work great. I have too much muscle memory from my centefires. I would hope to transfer drills and posture
Any assistance would be greatly appreciated.
Cheers
My question is hand guard. Are there any available that are long enough for a proper C grip. 16 inches and up would work great. I have too much muscle memory from my centefires. I would hope to transfer drills and posture
Any assistance would be greatly appreciated.
Cheers
If you go with an SBI chassis they also make a top enclosure piece you can add.
https://magdump.ca/1022-chassis-parts/513-spectre-g3-1022-chassis-xl-handguard-enclosure.html
I like my spectre chassis too but if u want a C grip, i think the Midwest Industries wud be the ticket.
But there is a guy on GP and here too so ewhere who hase a pretty cool 3D printed chassis with enclosed forend.
Affordable too although they just went up 25%. Yeesh.
But there is a guy on GP and here too so ewhere who hase a pretty cool 3D printed chassis with enclosed forend.
Affordable too although they just went up 25%. Yeesh.
- Location
- Edmonton Area Ab, Candle Lake Sk
MWI 13" Handguard (I have another I'd sell)
Barrel is a 12.5" SBI with a Dlask Compensator 14" overall
Would work well with a 16" Barrel
Barrel is a 12.5" SBI with a Dlask Compensator 14" overall
Would work well with a 16" Barrel
- Location
- Edmonton Area Ab, Candle Lake Sk
The printed Chassis would be ok for plinking, grip attachment may not hold up. Mine needed to be glued , Grip is not removable now.
These are very nice! Do they fit on all receivers though?
From what I've heard they need modification to fit on most aftermarket receivers because anything with an extended pic rail on the front interferes with the handguard.
Is this correct?
- Location
- Edmonton Area Ab, Candle Lake Sk
Yes .They do not fit Receivers that over hang the barrel , such as SBI , Dlask. Works well with Ruger Receivers.
For full size 16" barrel type rigs Midwest Industries or the Hera mentioned earlier in this thread might be your best bets.
I know for sure the SBI receiver (and probably most aftermarket receivers with the picatinney overhang at the front) will not fir the Midwest chassis but cannot speak about the Hera.
