CZ 457 Upgrades?

0faustus0

CGN Ultra frequent flyer
Rating - 100%
44   0   0
I might have caught the CZ457 fever …. I now have 3 of those babies … :rolleyes:



So, what are parts that are known to break over time on these CZ 457s?

I am hearing that a common issue is that the plating of the firing pin will come off over time.


What are other parts that are known to break and where it would make sense to replace/upgrade?


Other useful upgrades with respect to reliability …. ??
 
Only 'some' of the FPs lose plating. Most are OK, but I'd take the Bolt apart and look anyway. Likely to have 'drying grease' in there, and you can re-profile the tip while there. And the "c0cking indicator" might bend and cause the action to stick . . . I never look at mine anyway. I know when I c0ck a rifle. Never an issue with my VMTR.
You might want to put a Jard in one of you rifles if you want a super light trigger. I have a Timney and it's at ca 5-oz - good enuf for me but Jards can go lighter.
 
Only 'some' of the FPs lose plating. Most are OK, but I'd take the Bolt apart and look anyway. Likely to have 'drying grease' in there, and you can re-profile the tip while there. And the "c0cking indicator" might bend and cause the action to stick . . . I never look at mine anyway. I know when I c0ck a rifle. Never an issue with my VMTR.
You might want to put a Jard in one of you rifles if you want a super light trigger. I have a Timney and it's at ca 5-oz - good enuf for me but Jards can go lighter.
I have both Jard and Timney. My Timney wont go lower than 9.6oz. What did you do to lower yours to 5oz.
 
Only 'some' of the FPs lose plating. Most are OK, but I'd take the Bolt apart and look anyway. Likely to have 'drying grease' in there, and you can re-profile the tip while there. And the "c0cking indicator" might bend and cause the action to stick . . . I never look at mine anyway. I know when I c0ck a rifle. Never an issue with my VMTR.
You might want to put a Jard in one of you rifles if you want a super light trigger. I have a Timney and it's at ca 5-oz - good enuf for me but Jards can go lighter.
Os there any issue with just tossing the c0cking indicator in the garbage? I had mine apart the other day and was wondering if I could leave it out.
 
gun runner -
Just crank the screws to Lower Pull And reduce the 'Overtravel' to nearly Zero. Also, if you're using a digital gage you need to Watch AND Listen. On my Wheeler digital I can Hear the FP clik but CANNOT release the trigger before it hits the "Overtravel Wall", ie the End of Travel. Thus I often get readings ca 9-13 oz, But if I Watch the gage and Listen to the FP I can SEE the gage is at 5-oz when the FP clliks. I mentioned this to the YT video at
- see my comment ( @ed1099 - 3-years ago ) and also the other vid I mention there. (
- sort this by "Newest" and my post will be near the top - @ed1099 ) He also has other vids about accuracy and Timney adjustment.
Also a thread on RFC on this topic, My post is #25 - http s://www.rimfirecentral.com/threads/best-aftermarket-cz-457-trigger.1316447/
PS - Is your Timney rated for 'Low Pull' ? They make 3-diff levels I believe.

Bustercluck - I don't know if the FP would care, prob not. There are metal replacements made by some members on RFC, not super complex. You could prob make one with a file and a piece of brass chucked in a drill . . .
 
Back
Top Bottom