Any update on 7.62 mm manufactured parts?
- Thread starter millwright
- Start date
I have received dealer samples of several of thier parts and have been very pleased.
However I am not sure if they have applied for the export permits to begin selling retail to canada. I've been way to busy to follow up with them for the past month or so.
We should have some of thier parts at the december 11th m14 clinic to discuss and show around...... but none for sale as of yet..... though i am on thier dealer list.
However I am not sure if they have applied for the export permits to begin selling retail to canada. I've been way to busy to follow up with them for the past month or so.
We should have some of thier parts at the december 11th m14 clinic to discuss and show around...... but none for sale as of yet..... though i am on thier dealer list.
Chromed Firing Pin
Flash Hidder
There hammer's are so hard the it distroyed 2 bastard file's. There roll pin's set's work perfectly on or Norinco's and also there ejector & extractor spring set's are mint.
I would show you pic's of there bolt's but unless the owner who frequently uses this site give's me the okay I won't spoil his christmass present
Flash Hidder
There hammer's are so hard the it distroyed 2 bastard file's. There roll pin's set's work perfectly on or Norinco's and also there ejector & extractor spring set's are mint.
I would show you pic's of there bolt's but unless the owner who frequently uses this site give's me the okay I won't spoil his christmass present
Chromed Firing Pin
Flash Hidder
There hammer's are so hard the it distroyed 2 bastard file's. There roll pin's set's work perfectly on or Norinco's and also there ejector & extractor spring set's are mint.
I would show you pic's of there bolt's but unless the owner who frequently uses this site give's me the okay I won't spoil his christmass present
you have my permission
LOLOkay since you don't mindyou have my permission
Nork(LIGHT GREY) on bottom 7.62mm (DARK GREY) on top.
Note the roller is loose and wiggles. When I put it inside of M14 the headspace gauge reads 1.6355 dead on.
As for there extractor detent & spring combo (Shorter, Darker Color 1), once installed you know why the stock norks (Longer, Lighter Color 1) have ejecting issues with there's. See pic's bellow;
There ejector spring and detent there is no difference except the light color park on the nork(A Little Fatter) & the dark park on the 7.62mm(Thinner);
Now please do not go out and purchase the extractor as the 1 I received from them is not only has a smaller post but also is missing the top part of the round grabbing clip noted bellow;
If there is anything else you guy's might be interested in me posting pic's on post back and I'll try to fill ya in to the best of my ability.
Sorry Different there wasn't any that I could see. They have been having a real hard time making them and I don't really know why. Although these are not the first 1's I have seen. They did have an earlier batch that was recalled. I will try to find that website that had the pic's and reason's for ya.
- Location
- Western BC
Buyer beware....it has been 9 months and still no bolt from 762. A new excuse each month.
mountainspruce you are absolutely right. I have heard every step of F'up's that they had from parking it so bad that it literally looked like 200 grain sand paper to an over side locking lug & with this 1 that wasn't supposed to be shipped to me that has improper bolt roller.
Different I am sorry I have been trying to find the info for ya but the thread that was up on another website is missing.
Different I am sorry I have been trying to find the info for ya but the thread that was up on another website is missing.
I'll be inspecting that bolt Satain has with my guages, might even look into getting it rockwell tested depending on how much that's gonna ding me.
the loose bolt roller is of some concern but i have seen that on many a chinese bolt and they aren't falling apart. perhaps a USGI roller and clip will tighten it up a wee bit. We'll see at the clinic this weekend and I'll post my thoughts.
the loose bolt roller is of some concern but i have seen that on many a chinese bolt and they aren't falling apart. perhaps a USGI roller and clip will tighten it up a wee bit. We'll see at the clinic this weekend and I'll post my thoughts.
Satain, I appreciate the effort to find the other posted information.
M14Doctor, it cost me $50.00 to have a Chinese M14 bolt cut up and checked for core and surface hardness at a metal heat treater here in Las Vegas. FWIW and YMMV
M14Doctor, it cost me $50.00 to have a Chinese M14 bolt cut up and checked for core and surface hardness at a metal heat treater here in Las Vegas. FWIW and YMMV
