Overstock Gen4 G17s
- Thread starter Chuckbuster
- Start date
Ive heard reports of the slide coating isnt as durable on the USA ones, but i'm sure most of that is hive-mind speculation based on one or two questionable reports.
I was a late comer and mine is a USA made one. I guess the idea of it is a little dissapointing, but if i actually look at the situation its really a moot point. I (we) got a fantastic handgun for below dealer cost, and i doubt that glock would allow quality to suffer regardless of where its made. I'm pleased with my gun. I'll buy from PR again for sure.
I was a late comer and mine is a USA made one. I guess the idea of it is a little dissapointing, but if i actually look at the situation its really a moot point. I (we) got a fantastic handgun for below dealer cost, and i doubt that glock would allow quality to suffer regardless of where its made. I'm pleased with my gun. I'll buy from PR again for sure.
aka_ricerocket
New member
- Location
- Victoria B.C.
Looks like I'm getting 2 USA made ones in a few days. A little bit upset. but what can ya do. *fingers crossed for Austria made ones* highly doubt it though from what I'm hearing 
Unfortunately it is true the finish on the US one sucks and if Austrian ones are the same then glock just managed to create a finish that is worse than the original Springfield XD finish. I have one of those Springfield guns and after 6 years of use its finish looks better than my new glock I have had less than 24 hours. Maybe it will be fine over time but I just don't think it is going to hold up. It really is too bad as my gen 3.5 still looks new, glock used to have a very tough finish.
Last edited:
I read up on it, and apparently the Tennifer process they used to use on the slides violates a bunch of health and safety codes in the states because of the by products it creates, and is thus illegal. The slides are still hardened to the same amount as before, but the coating is slightly different, and can vary wildly on the mix and person running the batch so it can have varying colors across the same models etc.
FreedomIsn'tFree
CGN Ultra frequent flyer
- Location
- Republic of Buffalo.
Mine is a dark grey color and is very different from my Other Glocks. I have a Gen3 17 and 22 as well as a Gen4 17. My Gen3 17 has been used for a few years and has been holstered thousands of times and shows very little wear. I will keep my USA Glock and see how it stands up against my Gen3. It is already starting out with a small scratch from new, so time will tell. I think this may end up being a bad move for Glock.
I've been seeing this too, with the twist extra that Glock has not used the 'classic' Tenifer process since 2011. So it really doesn't matter if it's an American or Austrian built/assembled pistol. Sign 'o the times.
It's hard to nail down any exact sources. Just trying to piece this together from various reports from Glock Armorers, articles, and forum postings. There's apparently some interesting details on the process itself in Peter Kokalis' Weapons Tests And Evaluations: The Best Of Soldier Of Fortune.
Search on 'tenifer' on glock.com and you'll find a total of zero articles.
Anyone have access to any official press releases? Or is this is in the domain of corporate secrets?
It's hard to nail down any exact sources. Just trying to piece this together from various reports from Glock Armorers, articles, and forum postings. There's apparently some interesting details on the process itself in Peter Kokalis' Weapons Tests And Evaluations: The Best Of Soldier Of Fortune.
Search on 'tenifer' on glock.com and you'll find a total of zero articles.
Anyone have access to any official press releases? Or is this is in the domain of corporate secrets?
Burnaby,
Point taken. What makes a Glock a Glock will remain proven at the range. I'm positive that there will be no difference, regardless of finish or which plant ultimately assembles the infamous pistol.
However, as a student of history, I'm compelled to try and nail down the details. It's fascinating/frustrating how elusive any official details are.
But that doesn't reflect on the overall quality of firearm nor the dealer who is responsible for an awesome price.
Point taken. What makes a Glock a Glock will remain proven at the range. I'm positive that there will be no difference, regardless of finish or which plant ultimately assembles the infamous pistol.
However, as a student of history, I'm compelled to try and nail down the details. It's fascinating/frustrating how elusive any official details are.
But that doesn't reflect on the overall quality of firearm nor the dealer who is responsible for an awesome price.
Everything i've read has been second hand discussion on boards etc. I havent seen any sort of true press release from glock on changing the process.
http://glocktalk.com/forums/showthread.php?t=1446185
http://glocktalk.com/forums/showthread.php?t=1446185
Just ended up with mine.. its a USA one, come with a little scratch on the slide , no big deal , but i had it at the range and could only load 8-9 into the mags, more of an issue for me is one spent casing from from every mag was hitting me square between the eyes .. Common problem to anyone else?
Thanks Jon
Thanks Jon
Got back from the range with mine and it functioned perfectly. Casings ejected and didn't hit me.
Very reliable gun, no misfeeds, jams or other issues. I was using cheap aluminum-cased ammo too.
My Glock is marked "Made in Austria".
Very reliable gun, no misfeeds, jams or other issues. I was using cheap aluminum-cased ammo too.
My Glock is marked "Made in Austria".
Last edited:
Talk with Clay, pretty sure they'll swap out your mags with some that are properly "pinned".
If your not used to Glock's you might also have to watch that your thumb isn't riding the slide stop. Coming from a cz-75 I kept resting my thumb on the stop with my m&p and my slide wasn't staying locked back until I realized what was up.
Not sure if it would change anything since its not just my 3 mags that don't load 10. My friend also took advantage of this deal and all his mags also loads 9 rounds only.
Some people got the 17rnd mags pinned to 10. Those might fit the 10 rounds. All my mags were only the 10 rounder but should have been called a 9 rounder.
