6.5 x 55 - Headspace field gauge (M38 Swedish Mauser)

thirdeye462

Member
Rating - 0%
0   0   0
Location
Toronto, ON.
Hi all,

Checking in to see whether anyone here in the hive mind might have a 6.5 x 55 headspace field gauge they'd like to part with before I purchase a new one off of Manson or Forster. I just got a purpose-built M38 Husky (1942) arsenal refurb (bolt matches receiver). Gonna get the whole thing inspected all the same, but thought having a field gauge would be nice.

Searched the EE, but no go (pun intended).

Thanks!
 
I had read that Regimental gauges as used at Carl Gustaf Armoury were longer than SAAMI set standards for - so much so that a Swede GO gauge was LONGER than a SAAMI FIELD gauge. As a result, a "new" from CG Arsenal rifle would "fail" a SAAMI gauge headspace test. There might be merit though, if using SAAMI compliant ammo (virtually any North American maker), that one should have a SAAMI compliant chamber in the rifle. I had read that many Swede rifles, when imported into USA, were "fixed" by American gunsmiths, because they "failed" a headspace check.

I do not know what gauges were used by Husqvarana - but SAAMI is an American entity, so it would surprise me if Husqvarna used those standards for production to be used in Sweden - since Sweden tended to make their own standards - and had been using and making 6.5x55 for several decades BEFORE SAAMI even existed.

Sweden apparently did not adopt C.I.P. standards, but their own are very similar to C.I.P.'s.

It would also surprize me if the military armourers kept two sets of headspace gauges - one set for CG made stuff and another set for Husqvarna made stuff. I read that both the conversions done at CG from M96 rifles and the production from Husqvarna were all referred to as "M38" rifles, by the Swede military.
 
Hi all,

Checking in to see whether anyone here in the hive mind might have a 6.5 x 55 headspace field gauge they'd like to part with before I purchase a new one off of Manson or Forster. I just got a purpose-built M38 Husky (1942) arsenal refurb (bolt matches receiver). Gonna get the whole thing inspected all the same, but thought having a field gauge would be nice.

Searched the EE, but no go (pun intended).

Thanks!
If you find a good deal on a set (actually, I’m only interested in field) post it here. I mean, at the right price, I’d buy the whole set but for collectors determining if a chamber is safe for not, field is the only one that’s useful.
 
Hi all,

Checking in to see whether anyone here in the hive mind might have a 6.5 x 55 headspace field gauge they'd like to part with before I purchase a new one off of Manson or Forster. I just got a purpose-built M38 Husky (1942) arsenal refurb (bolt matches receiver). Gonna get the whole thing inspected all the same, but thought having a field gauge would be nice.

Searched the EE, but no go (pun intended).

Thanks!
I would rather have a GO GAUGE. One piece of masking tape added makes it a no go gauge. And that's all you need.
 
Checked a lot of 6.5x55 Swedish rifles when I had my shop. Never found one that wouldn't close on a SAAMI No Go.
I don't think there is much of a relationship between SAAMI and Swedish military standards.

Given a Husqvarna rifle with matching bolt, I would not bother buying a Field gauge. The likelihood of it being unsafe is negligible.
 
I had read that Regimental gauges as used at Carl Gustaf Armoury were longer than SAAMI set standards for - so much so that a Swede GO gauge was LONGER than a SAAMI FIELD gauge. As a result, a "new" from CG Arsenal rifle would "fail" a SAAMI gauge headspace test. There might be merit though, if using SAAMI compliant ammo (virtually any North American maker), that one should have a SAAMI compliant chamber in the rifle. I had read that many Swede rifles, when imported into USA, were "fixed" by American gunsmiths, because they "failed" a headspace check.

I do not know what gauges were used by Husqvarana - but SAAMI is an American entity, so it would surprise me if Husqvarna used those standards for production to be used in Sweden - since Sweden tended to make their own standards - and had been using and making 6.5x55 for several decades BEFORE SAAMI even existed.

Sweden apparently did not adopt C.I.P. standards, but their own are very similar to C.I.P.'s.

It would also surprize me if the military armourers kept two sets of headspace gauges - one set for CG made stuff and another set for Husqvarna made stuff. I read that both the conversions done at CG from M96 rifles and the production from Husqvarna were all referred to as "M38" rifles, by the Swede military.
This is really great info, Postashminer. Thanks for this.

"Sweden apparently did not adopt C.I.P. standards, but their own are very similar to C.I.P.'s." I was wondering about this. As I was looking into things, I was trying to figure out the SAAMI vs CIP question with respect to these Mausers, and it was really unclear to me whether gauges using either of these standards (outside the regimental gauges) are adequate enough or appropriate to tell you whether headspace is out of spec, especially after reading about how the chambers were cut generously on these things.

I did notice that Pacific Tool & Gauge carries field and "CIP max" gauges. It got me thinking about which is the most appropriate: https://www.pacifictoolandgauge.com/65-x-55-Swedish-SAAMICIP-Headspace-Gauges_p_114375.html


Can anyone point me to the 24-hour Carl Gustav regimental gauge store? :ROFLMAO:
 
I would rather have a GO GAUGE. One piece of masking tape added makes it a no go gauge. And that's all you need.
Actually, you got me thinking:

I guess I could do this with any available 6.5 x 55 gauge: keep adding tape to it until the stripped-down bolt doesn't close. Remove the gauge, measure its overall length and compare that measurement to the historical Swedish gauge measurements, which might be found in some literature or online somewhere. That would give me an indication of where things are at... :unsure:
 
I have no clue about where to get Sweden Regimental gauges - however, what I do - I bought a "cheapie" set of feeler gauges at Canadian Tire - I cut small circles from them - circa .470" or so - thinner ones cut with a scissors - thicker ones I had to use my tin snips or a file and hack saw. I use a small dab of grease on the bolt face to hold the circle there - any excess grease appears to "squish out" when the bolt is closed on a too tight gauge. - I am not overly surprized at a Swede rifle that closes (without feeling resistance) on a 0.014" shim behind a SAAMI GO gauge - I believe that is WAY past SAAMI FIELD length. I use a SAAMI GO gauge - that tells me how much longer that chamber and bolt is - versus SAAMI GO (SAAMI minimum) - may not be exact, but better, I think, than using brass cartridges to find "too long". I have used those same "shims" for multiple chamberings - 308 Win; 30-06, 8x57JS, 7x57, etc. besides 6.5x55 - GO gauges for the cartridge, in all instances.
 
This is really great info, Postashminer. Thanks for this.

"Sweden apparently did not adopt C.I.P. standards, but their own are very similar to C.I.P.'s." I was wondering about this. As I was looking into things, I was trying to figure out the SAAMI vs CIP question with respect to these Mausers, and it was really unclear to me whether gauges using either of these standards (outside the regimental gauges) are adequate enough or appropriate to tell you whether headspace is out of spec, especially after reading about how the chambers were cut generously on these things.

I did notice that Pacific Tool & Gauge carries field and "CIP max" gauges. It got me thinking about which is the most appropriate: https://www.pacifictoolandgauge.com/65-x-55-Swedish-SAAMICIP-Headspace-Gauges_p_114375.html


Can anyone point me to the 24-hour Carl Gustav regimental gauge store? :ROFLMAO:
IMHO, you're beating a dead horse.

If the bolt lugs are matching, don't show any signs of "set back" from over pressure loads, and the bolt lug recess faces in the receiver don't show any signs of set back, you're good to go.
 
When you say “purpose built” did that include changing the barrel?
Or does it have the original barrel to that receiver?

Remains to be seen. But my understanding is that it's "purpose-built" insofar as it's not a converted or cut down M96.

Very possible that the barrel's been swapped as it's an arsenal refurb. Once it arrives, I'll get a better idea.
 
This is really great info, Postashminer. Thanks for this.

"Sweden apparently did not adopt C.I.P. standards, but their own are very similar to C.I.P.'s." I was wondering about this. As I was looking into things, I was trying to figure out the SAAMI vs CIP question with respect to these Mausers, and it was really unclear to me whether gauges using either of these standards (outside the regimental gauges) are adequate enough or appropriate to tell you whether headspace is out of spec, especially after reading about how the chambers were cut generously on these things.

I did notice that Pacific Tool & Gauge carries field and "CIP max" gauges. It got me thinking about which is the most appropriate: https://www.pacifictoolandgauge.com/65-x-55-Swedish-SAAMICIP-Headspace-Gauges_p_114375.html


Can anyone point me to the 24-hour Carl Gustav regimental gauge store? :ROFLMAO:
You are maybe losing track why "headspace" is a thing - so that I can make ammo and you can make chamber and it will fit together - not too long and not too short - cartridge and chamber. I do not know if you hand load - within reason, "headspace" becomes a NON ISSUE - a hand loader should make his ammo fit to the chamber - whether that chamber is to someone's standard or not. But no assurance that the ammo that fits to an unknown chamber will fit to anyone else's rifle - or whether anyone else's ammo will fit to your gun. I have one - I turned a small ring Husqvarna barrel that was chambered in 9.3x57 into a Husqvarna Receiver - I wanted a "punkin chucker" - I have to make the brass from 8x57 since I have never seen any 9.3x57 ammo to buy. I could not get anyone's Headspace gauges to set that barrel - so I have no clue if this chamber is to anyone's spec or not. However, the rifle will accept brass made in my dies - good enough for me - I do not know or care whether this ammo will fit to anyone else's, but it does fit snuggly to my rifle. I do not know or care whether this chamber will fit (too long or too short) to someone else's hand load or to any factory ammo.

Headspace probably becomes very relevant if you are only going to use factory ammo - than then you will want to verify to who's standard is that stuff made - C.I.P. or SAAMI - there may or may not be a difference.
 
Last edited:
You are maybe losing track why "headspace" is a thing - so that I can make ammo and you can make chamber and it will fit together - not too long and not too short - cartridge and chamber. I do not know if you hand load - within reason, "headspace" becomes a NON ISSUE - a hand loader should make his ammo fit to the chamber - whether that chamber is to someone's standard or not. But no assurance that the ammo that fits to an unknown chamber will fit to anyone else's rifle - or whether anyone else's ammo will fit to your gun. I have one - I turned a small ring Husqvarna barrel that was chambered in 9.3x57 into a Husqvarna Receiver - I wanted a "punkin chucker" - I have to make the brass from 8x57 since I have never seen any 9.3x57 ammo to buy. I could not get anyone's Headspace gauges to set that barrel - so I have no clue if this chamber is to anyone's spec or not. However, the rifle will accept brass made in my dies - good enough for me - I do not know or care whether this ammo will fit to anyone else's, but it does fit snuggly to my rifle. I do not know or care whether this chamber will fit (too long or too short) to someone else's hand load or to any factory ammo.

Headspace probably becomes very relevant if you are only going to use factory ammo - than then you will want to verify to who's standard is that stuff made - C.I.P. or SAAMI - there may or may not be a difference.

Norma still loads and sells it.

It comes and goes (quickly). I bought 4 boxes of Norma brand 9.3x57mm it at a gunshow about 8 years ago for $30 each.

A LGS told me years ago after that they could get some in from a local distributor but wanted something like $98 a box plus taxes and I remember Trade-Ex used to have and sell it on occasion too.

9.3x57mm.jpg
 
I seem to recall that Norma published numbers related to 9.3x57 gauges - but different from CIP gauge numbers - I was going to get a set of headspace gauges to be ground - but could not find a specific spec to do so - so it did not happen. Somehow, Hornady Custom Grade dies showed up - labeled 9.3x57 - I have no clue where they got their data - but those are the dies that I used to form the brass cases that I used to set that barrel. So, as posted earlier - I still have no clue who's specs I used, if any were actually used. I have many boxes of .308 Norma Match, Ball 168 grs ammo, but I never did see any 9.3x57 rounds to buy.

IMG_2663.jpeg
 
Back
Top Bottom