ADM 30mm one piece mount

broncoo

broncoo

CGN frequent flyer
Rating - 100%
195   0   0
Location
kelowna
i know TSE sells em, does anyone else have them actually in stock

i am looking for the 30mm qd straight up no cantilever

putting a vortex 2.5-10x44 hs on my rfb (currently wears a burris pepr with a leupold vx3 2.5-8x36)


and i posted this here instead of the optics section because the guys in here might have a better idea where to get one
 
You can order right off their website, although you'll pay a bit more for the shipping and duties. Add 20 bucks for shipping and 40-ish for GST and duty.

You can also try Emailing Arms East as I think they do carry ADM stuff, give them the model number and ring size and see if they can order one for you or if they have a shipment coming in.

Awesome mounts, I've had one on my aimpoint micro for a good 2 years now and the new 1-piece (similar to the one you want, but mine was the LOW model) for my vortex Viper PST that's still waiting for a gun to put it on :p

I saw you posted in the last thread about it but wanted to post here too in case ya missed it.

Give it about a week or so for shipping if you order it online. Or again, you can try Arms East and see if they can order one in for ya on their next order (if they are still ordering stuff from ADM)
 
I thought I remember reading there was a guy that said he was selling ADM mounts, but I been searching for the post for the past few days and can't find it. I'am looking for the same mount, might just order it straight from the states.
 
Another CGNer told me to go to Grouse river to get mine, that is what I did! :D

I wanted the recon, should be in the mail as we speak
 
mrblue357 said:
Well I phoned this morning and they only have the RECON-SW model and not the S, wonder if that one would work ok.
Click to expand...

Depends on your optic but if you're mounting it on a flattop AR your best mount is the AD-Recon because of the built in 2" eye relief.

http://www.americandefensemanufacturing.com/view/product/195/
 
mrblue357 said:
Well I phoned this morning and they only have the RECON-SW model and not the S, wonder if that one would work ok.
Click to expand...

Yes it should work.

The PST 2.5-10x44 is listed at 5.6 inches from tube end to end, and the Recon SW is listed at being 5.2 inches total length.

It's meant more for the long tubed Schmidt and Bender scopes, but it should provide a very solid rigid mount for the scope (much moreso than needed)

dim_viper-pst_2-5-10x44.jpg


02.jpg


tainted_demon said:
Depends on your optic but if you're mounting it on a flattop AR your best mount is the AD-Recon because of the built in 2" eye relief.

http://www.americandefensemanufacturing.com/view/product/195/
Click to expand...

OP stated it was for his RFB, so the strait up mounts will give more options for eye relief and a stronger (less flexible) mount :)
 
mrblue357 said:
Thanks, I had a good look at that today so its definantly a option. Will be going on a Ar-15 or a XCR-M when I do get it.
Click to expand...

Oops just saw you were not the OP.

tainted_demon was most definitely correct for an AR15 flat top absolutely a cantilevered version, unless you have something like an LMT MRP or the VLTOR monolith railed upper.

For the XCR M then most definitely the strait-up mounts due to the reasons I had previously posted.
 
You must log in or register to reply here.
Back
Top Bottom