AR-15 gunsmithing, assembly, and modification services

[MAD_MAX333]

Sweet Jesus I been dying trying to find someone to put my parts kit of a garand together for me! Plus it has a blank barrel that I need threaded in 308. Can you do this? How much!? Lead time!? Save meeeeee

 

[VancouverS4]

are you able to cut and mill a barrel to have integrated porting for an 18.6" with a built in brake?

 

[True North Arms Corp]

So how do I get stuff to you guys? Mail?

Call the RCMP to get a temp ATT to the post office, then another one to pick it up after?

Our lay opinion is that if your license conditions allow transport to and from a gunsmith, then shipping it to a gunsmith is also allowed.

 

[True North Arms Corp]

Was just told it be another week or two. Is your anodizer here in Ontario?

Yes

 

[True North Arms Corp]

are you able to cut and mill a barrel to have integrated porting for an 18.6" with a built in brake?

We don't have the equipment for this (mill and dividing head), so can't do at this time, sorry.

 

[halv18]

Can you mill handgun slides to accept RMR optics?

 

[Donny Fenn1]

Artist's rendition of our gunsmith. What's he doing, turning a lathe headstock with a crescent wrench? That's not even a thing. And it's shooting sparks out the back, wtf

I think it's not sparks but an old school belt drive machine?

 

[True North Arms Corp]

Can you mill handgun slides to accept RMR optics?

sorry we don't have the machinery for this.

I think it's not sparks but an old school belt drive machine?

mm yes I didn't see it that way until you mentioned it.

I think I know what makes it turn --

 

[True North Arms Corp]

do you cut, crown and thread skss?

Sweet Jesus I been dying trying to find someone to put my parts kit of a garand together for me! Plus it has a blank barrel that I need threaded in 308. Can you do this? How much!? Lead time!? Save meeeeee

No to both, sorry

 

[VancouverS4]

We don't have the equipment for this (mill and dividing head), so can't do at this time, sorry.

Thank you for the reply

 

[Razor117]

Are you able to pin A2 gas blocks to barrels by chance?

Thanks in advance

 

[True North Arms Corp]

Are you able to pin A2 gas blocks to barrels by chance?

Thanks in advance

We are setting up for this. I'll PM you when it's ready

 

[Putz57]

We are setting up for this. I'll PM you when it's ready

Amazing! If you don't mind letting me know as well please!!

 

[True North Arms Corp]

Amazing! If you don't mind letting me know as well please!!

Will do

 

[snipersyn]

We can bore out your muzzle device for 9mm .40 cal and other pistol cartridges (works for most devices but not all, feel free to inquire).

Do you guys use a multi prong jaw or dedicated screw-on jig when you're reaming muzzle devices?

Are you able to accommodate non-round devices?

 

[A.Waterman]

May have missed this but if I purchased a barrel could you set it up for a traditional A2 FSB? Those 2 little grooves for the Taper pins?
Thanks in advance.
A.W.

EDIT: just read the top post of this page, will stay tuned.

 

[True North Arms Corp]

Do you guys use a multi prong jaw or dedicated screw-on jig when you're reaming muzzle devices?

Are you able to accommodate non-round devices?

We normally have a 3-jaw chuck but can swap in a 4-jaw for a square/rectangular workpiece. What have you got?

 

[jw8]

this could be promising.

would you be able to source a complete upper for a dpms 308. looking for 12.5 inch if there are any you can acquire, that would be nice.

 

[Texstar]

Look up aesthetic anodizing on Facebook. He does all sorts of will finishing.

 

[Patriot762x51]

Can you reprofill barrels my AR barrel it is to thick in some places ?