Browning BLR's

the only BAD thing about BLRs is there triggers NOT many are NICE ! :p
Yes, the triggers are terrible...
But after a bit of practice I learned where the creep broke, and have been able to produce 1" groups with it consistently, with a 220 gr Speer Hot Cor handload.
After years of using those handloads I was running low and tried the Hornady 200 gr ammo; it will produce 3 shot groups of 0.510" at 100 yards at 2469 fps from that 20" barrel. That's only 6 fps slower than spec'd, with a Standard Deviation of 8.8.
 
Have long been on the lookout for a 257 Roberts...
A fellow I used to work with has one of those BLRs. He's not a gun nut so would be just as happy to have a 308. I tried to get it from him but to no avail.

Many years ago I saw a new one in the LGS on a rack. I was quite surprised as it's not very common here at all. The reason I remember that gun in particular is that it came from the factory without sights nor was it drilled. That would be quite rare by anyone's standards.

I looked high and low for a Remington Mountain Rifle in 257R. Found one in Ontario but the old guy would not sell. I ended up having one built and am quite happy with the round.
 
I'm happy with the custom 257 Bob I got from Prophet River.
Beautiful firearm with high luster bluing and an exhibition grade walnut stock that was made by the late Lew Bates, whom I was an acquaintance of for many years. Happy to have a rifle with one his stocks!
It shoots the Nosler 110 gr AccuBond ammo into .582" groups at 100 yards.
And I am trying to develop a load for it with 115 gr bullets. I have one load showing promise with the Ballistic Tip and Re-22. The rifle's mag box os short and I cannot quite reach the recommended COAL for it, so am also going to try the 155 gr Partition and see if the flat based bullet gets me there, and therefore closer to the lands.
Having one of those rare BLRs in this chambering has long been a bucket list item.
 
A fellow I used to work with has one of those BLRs. He's not a gun nut so would be just as happy to have a 308. I tried to get it from him but to no avail.

Many years ago I saw a new one in the LGS on a rack. I was quite surprised as it's not very common here at all. The reason I remember that gun in particular is that it came from the factory without sights nor was it drilled. That would be quite rare by anyone's standards.

I looked high and low for a Remington Mountain Rifle in 257R. Found one in Ontario but the old guy would not sell. I ended up having one built and am quite happy with the round.
Now replaced by th 25 CM a true short action cartridge ;) :D
 
Now replaced by th 25 CM a true short action cartridge ;) :D
And I keep thinking that I should have one in 6.5 CM...I just find it hard to like the new alloyed action as compared to the older steel ones...and I have a bolt action and a High Wall that both shoot very well!
Perhaps I rebarrel an older one...will wait to see how well I like my 25 CM bolt action when finished.
 
Owned two. First one was in 308win. Ss pistol grip. Bought new. Was too nice to cary through the woods around here for general bear duty. So it didn’t get used much and I sold it.

Second was a ss takedown in 300wsm. Bought used had a little wear. Was my carry around bear gun. Carried nicely. Takedown was handy. Recoil was manageable. Lever was a little tough to operate on a fired case, gloves or a pad on the lever would have helped this. Sold it to buy a different bear gun.

Another one is on my list to buy again when the time/money is right. Ideally a rough handled short action one. So dragging it through the woods can be done without a second thought. If you’ve got one stock up on magazines while they’re still available new
 
is the length of lever-throw very much different than a short action? Have never compared myself
It makes a noticeable difference to me anyways...

51mm vs 63.mm in cartridge length, roughly 1/2".

May not appear much to some but one can notice the lever through. The bolt is also that much further away from your face when cycling...
 
It makes a noticeable difference to me anyways...

51mm vs 63.mm in cartridge length, roughly 1/2".

May not appear much to some but one can notice the lever through. The bolt is also that much further away from your face when cycling...
I think what box hitch was asking. If not I’m curious myself.

Are the long action guns and short action guns geared at different rates to make up for the 1/2ā€ of extra cartridge length and bolt throw? Maybe someone with both could be helpful and put a picture of two side by side with levers all the way open.
 
Short/long action have a different mag well and accordingly sized receivers. Long action is heavier too, usually...
 
Back
Top Bottom