Copper fouled barrel?? 308

Yes, I agree. I have two old rifles with some really old and heavy cupronickel fouling. It doesn't want to come out with anything. What do you use?
Old school armourers used an issued "Magic Juice" and very specific instructions/process to remove that stuff - it was ammonia based, I think - sort of a race between getting that fouling out and ruining the barrel steel finish.

But, they were in an environment with MANY extra barrels, so if they ruined one by not following procedures, there were plenty more that could be "spun on" - many modern folk are not in that situation
 
Old school armourers used an issued "Magic Juice" and very specific instructions/process to remove that stuff - it was ammonia based, I think - sort of a race between getting that fouling out and ruining the barrel steel finish.

But, they were in an environment with MANY extra barrels, so if they ruined one by not following procedures, there were plenty more that could be "spun on" - many modern folk are not in that situation


I've tried ammonia based stuff, even straight ammonia before. Didn't touch it. When I looked it up it lists certain chemicals to use, which are a bit more difficult than to just buy. With nothing available off the shelf to remove it.
 
I do not think cupronickel has been used for bullet jackets in past 100 years, so not really surprizing to hear that no one is making or selling something to remove it, today. The process involved a "soak", as I recall reading about it - not on a patch pushed through the bore. I think the bore was capped and the Magic Juice was poured into the bore for a specific amount of time - as I recall reading, ammonia was not the only active ingredient in that Juice.
 
Just clean the rifle, since you’re all over the place anyways….

You do carry on like a squirrel with ADHD with your approach to things it seems.
.

I am more than likely in that bracket , the more I get older an learn about myself..

I would most likely seem that way from the outside yes 👍🫎


An there is no such thing as a dumb question, right 😎
 
Yes.

The process and the end result of that process are exactly the same thing. Copper fouling from shooting copper jacketed bullets. Where did you think the yellow stuff came from? :rolleyes:



Yes.

It is a known issue and perfectly normal. 🤷‍♂️

You pushed a copper clad bullet down the bore at high velocity and that leaves copper fouling in the bore. This is about as simple 1+1=2 kind of logic. Not sure how you don't get that? Maybe rub some brain cells together and see how that works out? 🤷‍♂️
Ahh I see says the blind man to his deaf son 😂👍
 
Saying there are no such thing as a dumb question is like giving participation ribbons to everyone. It's aimed at preventing hurt feelings.

There are dumb questions that get asked!

There are no stupid questions. Only stupid people.

Jokes aside it seems better to ask than not know. Ask the question. Whoever judges it has done/said something just as dumb in their lifetime anyway lol.
 
Apart from leading with cast I've never seen this in my barrels , so why not post the dumbest question on CGN!?
I understand it's more fun to debate 308 v 3006 but still, that's dumb
😂

I think its interesting! Brother you actually shoot! How have you not seem coppered bores yet? haha
 
I think its interesting! Brother you actually shoot! How have you not seem coppered bores yet? haha
I'm hearing you!!
That's why I asked if it is a fouled barrel or just some #### off the jacket , as in did it needs a full blown wipeout , or is it mildly normal . Lol.

That still grinds some hears though I see 😂
 
The most common phrase in any gun-cleaning discussion. And one I have never understood. Why would anybody want accuracy to degrade before cleaning their bore? Why not clean it before you lose accuracy. Why wait to miss something or shoot a poor score before cleaning?It really isn't that difficult.
It depends on your version of accuracy.

There are lots of good reasons to wait for accuracy to deteriorate before removing the fouling.

Most shooters just don't shoot enough to warrant an in depth cleaning after every trip to the range.

If you're a match shooter, or a wannabee match shooter, then you quickly figure out how many rounds down the bore before accuracy deteriorates, especially if you need a prescribed number of rounds for a score in one sitting.

Then, of course, after every cleaning, rezeroing is pretty much mandatory for most rifles, other than the very odd unicorn.
 
Would it be possible to 'miss' an animal under fairly standard scenarios with a fouled barrel?
I don't think so sub 300 meters- majority fall well into this bracket.

I've actually been developing loads with this particular gun , loading charges up 1gr increments , with a couple different projectiles ... So I hadn't noticed nor had the default load to compare accuracy to 😎


I'll touch base when I've had a shot thru it next and run some copper remover thru it 🤙
 
What doesn't hahaha

Definitely some electric blue patches in your future. But, no accuracy change? lol.
Read above mate.

It's zeroed for Her downloaded 150 gr loads.... But with mid to full power 180gr loads the same Zero works (eg 150g +2 inch at 100. & 180gr Bang on at 100m )

So I got interested in playing with 180grainers in it so as I can thump something solid with it in near future- not with her bullets haha.

We haven't shot a group with her 150s in a while TBH , hence can't really comment on yay or nay , an I'm getting MOA groups here an there with developing 180 fodder an hadn't tested enough RE seating to confirm a solid Heavy load yet 👍

Hope that makes a bitta sense on the situation
 
Back
Top Bottom