Cz 452

[chappy]

mine likes sk+ but cci standard velocity is pretty good too.

 

[Kody]

I must have a bastard sized CZ 'Merican because none of those measurements in that chart
resemble the wide girth of my dovetail.
Arf inch and some.

Kamlooky, You probably know this but in case you don't, the 3/8 dovetail measures 3/8 at the base not at the top. The 11mm is measured at the top. Took me a while before I realized that....

 

[purplemushroom]

Nice, I've been lookin for one of these for a while

 

[vrex]

Kamlooky, You probably know this but in case you don't, the 3/8 dovetail measures 3/8 at the base not at the top. The 11mm is measured at the top. Took me a while before I realized that....

 

[Kody]

That's it! Thanks vrex.

 

[kamlooky]

Haven't found a set of rings to fit proper other than the cheap Scorpions that came with a rimfire scope.
Need to purchase a set of CZ rings and be done with it.

 

[Shooter_01]

Haven't found a set of rings to fit proper other than the cheap Scorpions that came with a rimfire scope.
Need to purchase a set of CZ rings and be done with it.

I'm leaning towards this, as well. Where would one purchase CZ rings for a 452 American?

 

[Cardamonfrost]

I found that the Burris Signature Zee fit perfectly in medium (I have irons too). That was in a 1 inch tube, not tonnes, but enough bolt clearance, 40 mm obj I think?.

C

 

[dimeN]

http://w ww.talleymanufacturing.com/Products/Rimfire-Specialty-Rings/CZ-%281%29.aspx

i got the high mounts

 

[midnightpossum]

Haven't found a set of rings to fit proper other than the cheap Scorpions that came with a rimfire scope.
Need to purchase a set of CZ rings and be done with it.

I run this BKL mount on my 452.. not much room for the bolt handle, but it works. I really like that it is 1 piece

 

[Kody]

Haven't found a set of rings to fit proper other than the cheap Scorpions that came with a rimfire scope.
Need to purchase a set of CZ rings and be done with it.

Kamlooky, I know what you mean!
Just have a look at these options that I think fit fine and will not cost you as much as the CZ rings:
I have a 512 with Talley rings and the fit is perfect; probably the best fitting rings out of what I have tried. I just don't like how they look on a bolt action CZ otherwise I would use them on all of my CZs. You can get 3/8 or 11 mm version from Prophet River. The rest of my CZs have Burris Signature Zee rings (weaver style) with J&P adapters or Burris deluxe steel 22 rings (3/8 in dovetail but also fit 11 mm very well). I have used BKL257 normal height and they fit very well. Unfortunately they were too high for what I needed.
My next CZ will get the Burris Signature Rimfire & Airgun Rings that come with 2 sets of clamps, one for 11mm the other one for 3/8. No adapter required. Apparently they fit really well as per what people say on Rimfire Central.

 

[hoytcanon]

My 452's shoot very well with CCI SV's and SK St.+... as far as mounts go... the FS and Varmint are scoped with rings on DIP rails... takes out the guess work and expense of Talleys... still very low profile...




Here is a ten shot group I shot last weekend, checking the gun before a bunny hunt, at 50 meters with the FS off the truck hood on my bundled jacket. Half inch squares.

 

[hometownhero]

I have a dip extended rail on my scoped cz's. Can use any weaver ring I want to.

 

[dimeN]

@ Hoyt

great shooting ! that manlicher stock is so sweet ... I like the look but have never owned one ( thats what will be next ... )